2007-2013 Highlander Kluger · Service Manual STEERING

Steering Lock Motor Drive Power Circuit

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The steering lock ECU is connected to the main body ECU and certification ECU (smart key ECU assembly). The steering lock ECU cannot activate the motor unless it receives permission signals from both ECUs. (The main body ECU permits the steering lock ECU to supply power to activate the motor.)

WIRING DIAGRAM

C113485E15

INSPECTION PROCEDURE


1. CHECK VEHICLE CONDITION
  1. Check the problem symptom of the steering lock system.

    Result:
    Condition
    Proceed to
    Steering lock cannot be released
    A
    Steering cannot be locked
    B



B
Go to step 6
A


2. READ VALUE USING INTELLIGENT TESTER
  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry & Start / Data List.

  1. Select the item below in the Data List, and read its value displayed on the intelligent tester.

    Entry & Start: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Lck/Unlck Rec
    Steering lock command reception record / YES or NO
    YES: Steering lock / unlock signal received
    NO: Steering lock / unlock signal not received
    -

  1. Check if a steering unlock command signal has been received.

    OK:
    "YES" is displayed on the tester display.



NG
CHECK SMART ENTRY AND START SYSTEM (Click here)
OK


3. INSPECT STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)

  1. C157849E13
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D10-3 (IGE) - D10-1 (GND)
    1. Engine switch off
    2. Engine switch on (ACC or IG)
    1. Motor activated: Below 1 V
    2. Motor not activated:
      11 to 14 V



NG
Go to step 4
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

4. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - BODY GROUND)

  1. C157850E15
    Disconnect the D10 connector from the steering lock actuator assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D10-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - MAIN BODY ECU)

  1. C157851E03
    Disconnect the D7 connector from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D10-3 (IGE) - D7-19 (SLR+)
    Always
    Below 1 Ω
    D10-3 (IGE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

6. INSPECT STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)

  1. C157849E15
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D10-3 (IGE) - D10-1 (GND)
    The specified condition should be checked after performing the following:
    1. Move the shift lever to the N position
    2. Turn the engine switch off
    3. Open the driver's door
    1. Motor activated: Below 1 V
    2. Motor not activated:
      11 to 14 V



NG
Go to step 7
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

7. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - MAIN BODY ECU)

  1. C157851E03
    Disconnect the D10 connector from the steering lock actuator assembly.

  1. Disconnect the D7 connector from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D10-3 (IGE) - D7-19 (SLR+)
    Always
    Below 1 Ω
    D10-3 (IGE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← B2788 IG2 Signal Malfunction (from Jul 2010)Steering Lock Motor Drive Power Circuit (Aug 2008 – Jun 2010) →