2007-2013 Highlander Kluger · Service Manual STEERING

B2788 IG2 Signal Malfunction

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The steering lock ECU determines the on/off status of the engine switch through the IG2 signal circuit.
After receiving an IG2 relay ON signal, the steering lock ECU determines that the vehicle is moving. The steering lock ECU does not lock the steering when it receives the IG2 relay ON signal. This prevents the steering from being locked while the vehicle is moving.
The diagnosis information of the steering lock ECU is transmitted to the tester via the certification ECU (smart key ECU assembly) as the steering lock ECU is not connected to the CAN communication system.
DTC No.
DTC Detecting Condition
Trouble Area
B2788
Different information is obtained from IG2 signals received directly from the IG2 circuit, and from IG2 signals sent via LIN communication for a period of 1 second.
  1. IG2 relay
  2. Wire harness
  3. Main body ECU
  4. Steering lock actuator assembly (Steering lock ECU)

WIRING DIAGRAM

C172489E02

INSPECTION PROCEDURE

When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following step to wake up the ECU:
Before starting the inspection, with the engine switch off, open the driver's door. Then (with the engine switch still off) open and close any door several times in 1.5-second intervals.

NOTICE:
If the steering lock actuator assembly (steering lock ECU) is replaced, with the engine switch off and the shift lever in the N position, open and close the driver's door to record the current lock position into the steering lock ECU. If this is not performed, the engine may not start.


1. INSPECT IGNITION RELAY NO. 2 (IG2)

  1. B060778E75
    Remove the IG2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Always
    10 kΩ or higher
    3 - 5
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE IGNITION RELAY NO. 2 (IG2)
OK


2. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - BODY GROUND)

  1. C157850E13
    Disconnect the D10 connector from the steering lock actuator assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D10-1 (GND) - Body ground
    Always
    Below 1 Ω
    D10-2 (SGND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - BATTERY)

  1. C157850E14
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D10-6 (IG2) - D10-1 (GND)
    Engine switch on (IG)
    11 to 14 V
    D10-6 (IG2) - D10-2 (SGND)
    Engine switch on (IG)
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    *D10-6 (IG2) - D10-7 (B)
    Engine switch off
    10 kΩ or higher

    *: This measurement is performed with the engine switch off to check for a short between IG2 and battery voltage.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - BATTERY)
OK

REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)


← B2788 IG2 Signal Malfunction (Aug 2008 – Jun 2010)Steering Lock Motor Drive Power Circuit (May 2007 – Jul 2008) →