2007-2013 Highlander Kluger · Service Manual ENGINE

Engine does not Start

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION


ENGINE START SYSTEM FUNCTION
  1. If the engine switch is pressed with the shift lever is in the P or N position and the brake pedal depressed, the main body ECU determines that it is an engine start request.

  2. The certification ECU (smart key ECU assembly) and other ECUs perform key verification via the LIN communication line.

  3. The main body ECU activates the ACC relay.

  4. The main body ECU activates the IG1 and IG2 relays.

  5. The certification ECU (smart key ECU assembly) outputs a steering UNLOCK signal. The signal is sent to the main body ECU via the steering lock ECU.

  6. The main body ECU sends an engine start request signal to the ECM.

  7. The ECM sends an ACC cut request signal to the main body ECU.

  8. The ECM and main body ECU activate the starter relay.

  9. The main body ECU deactivates the ACC relay until the main body ECU detects an engine start.

  10. When engine revolution speed reaches 1200 rpm, the ECM determines that the engine has been started.

    Symbol of main body ECU
    Signal
    STP
    Stop light switch ON signal
    Input
    SSW1/SSW2
    Engine switch ON signal
    Input
    ACCD
    ACC relay operation signal
    Output
    SLP
    Steering lock actuator position signal
    Input
    IG1D
    IG1 relay operation signal
    Output
    IG2D
    IG2 relay operation signal
    Output
    STR2
    Starter relay operation signal (Sub)
    Output
    STR
    Park/Neutral position switch signal
    Input
    TACH
    Engine start detection signal
    Input
    STSW
    Starter activation request signal
    Output
    ACCR
    ACC cut request signal
    Input
    Symbol of ECM
    Signal
    ACCR
    ACC cut request signal
    Output
    TACH
    Engine revolution speed signal
    Output
    STSW
    Starter activation request signal
    Input
    STAR
    Starter relay operation signal (Main)
    Output
    STA
    Starter activation signal
    Input

B175596E03
B172608E01

WIRING DIAGRAM

See "CRANKING HOLDING FUNCTION CIRCUIT" (Click here).

INSPECTION PROCEDURE


EMERGENCY ENGINE START CONTROL
  1. If there is a malfunction in the stop light switch circuit or STOP fuse, their signals may not be correctly transmitted to the main body ECU. This may result in the engine not starting even if the engine switch is pressed while the brake pedal is depressed and the shift lever is in the P position.
    To activate the starter:

    1. Turn the engine switch from off to on (ACC).

    2. Press and hold the engine switch for 15 seconds.

HINT:
If the main body ECU is replaced with a new one while the negative (-) battery terminal is connected, the power source mode will be in IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU, certification ECU (smart key ECU assembly), steering lock ECU, ID code box (immobiliser code ECU) and/or ECM are/is replaced, perform the registration procedure for the engine immobiliser system.


1. CHECK THE ENGINE SWITCH CONDITION
  1. Check that the power source mode changes.

    1. When the key is inside the vehicle and the shift lever is in the P position, check that the power source mode changes.

      OK:
      off → on (ACC) → on (IG) → off



NG
GO TO OTHER FLOW CHART (Click here)
OK


2. CHECK DTC
  1. Delete the DTCs (Click here).

  1. Check for DTCs again.

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    No DTC is output
    A
    Smart entry and start system (starting function) DTCs are output
    B
    Steering lock DTCs are output
    C
    Engine immobiliser system DTCs are output
    D
    Vehicle stability control system DTCs are output
    E



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (SMART ENTRY AND START SYSTEM (STARTING)) (Click here)

C
GO TO DIAGNOSTIC TROUBLE CODE CHART (STEERING LOCK SYSTEM) (Click here)

D
GO TO DIAGNOSTIC TROUBLE CODE CHART (ENGINE IMMOBILISER SYSTEM) (Click here)

E
GO TO DIAGNOSTIC TROUBLE CODE CHART (VEHICLE STABILITY CONTROL SYSTEM) (Click here)
A


3. CHECK CRANKING FUNCTION
  1. Check the engine cranking function.

    1. When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch crank the engine.

      Result:
      Result
      Proceed to
      Engine cranks
      A
      Engine does not crank
      B



A
GO TO SFI SYSTEM (Click here)
B


4. READ VALUE USING INTELLIGENT TESTER (STARTER CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Read the DATA LIST according to the displays on the tester screen.

    ECM: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Starter Control
    Starter switch signal / ON or OFF
    ON: Engine switch on (ST)
    OFF: Engine switch except on (ST)
    -

    Standard:
    Engine switch condition
    Tester display
    When engine switch is on (ST)
    ON
    When engine switch is except on (ST)
    OFF



NG
Go to step 10
OK


5. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STARTER RELAY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Perform Active Test according to the prompts displayed on the tester.

    ECM: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Starter Relay
    Starter
    ON or OFF
    -

  1. B177522E01
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Starter relay terminal 2 - Starter relay terminal 1
    When starter relay is ON by Active test using intelligent tester
    8 to 14 V
    Starter relay terminal 2 - Starter relay terminal 1
    When starter relay is OFF by Active test using intelligent tester
    Below 1 V



NG
Go to step 20
OK


6. INSPECT STARTER RELAY

  1. B016200
    Remove the starter relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE STARTER RELAY
OK


7. CHECK HARNESS AND CONNECTOR (STARTER RELAY TERMINAL VOLTAGE AND RESISTANCE)

  1. B177522E01
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Starter relay terminal 5 - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Starter relay terminal 1 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR, OR REPLACE FUSE
OK


8. CHECK HARNESS AND CONNECTOR (STARTER RELAY - STARTER)

  1. Disconnect the B12 connector.B177908E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block starter relay terminal 3 - B12-1
    Always
    Below 1 Ω
    Engine room relay block starter relay terminal 3 or B12-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY - STARTER)
OK


9. CHECK HARNESS AND CONNECTOR (BATTERY - STARTER)

  1. B178243E01
    Disconnect the C1 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    C1-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STARTER)
OK

REPLACE STARTER ASSEMBLY (Click here)

10. READ VALUE USING INTELLIGENT TESTER (PARK/NEUTRAL POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Read the DATA LIST according to the displays on the tester screen.

    Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    N SW / C SW
    Park/Neutral position switch / ON or OFF
    ON: Shift position is P or N
    OFF: Shift position is not P or N
    -

    OK:
    "ON" (Shift position is P or N) and "OFF" (Shift position is not P or N) appear on the screen.



NG
Go to step 14
OK


11. READ VALUE USING INTELLIGENT TESTER (S CODE)
  1. Connect the intelligent tester to the DLC3.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

  1. Turn the engine switch on (IG).

    Entry & Start: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    S Code Chk
    S code check / OK or NG
    OK: Normal
    NG: Malfunction
    -

    OK:
    "OK" is displayed on the screen.



NG
Go to step 24
OK


12. READ VALUE USING INTELLIGENT TESTER (L CODE)
  1. Connect the intelligent tester to the DLC3.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

  1. Turn the engine switch on (IG).

    Entry & Start: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    L Code Chk
    L code check / OK or NG
    OK: Normal
    NG: Malfunction
    -

    OK:
    "OK" is displayed on the screen.



NG
Go to step 29
OK


13. READ VALUE USING INTELLIGENT TESTER (IMMOBILISER SYSTEM STATUS)
  1. Connect the intelligent tester to the DLC3.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

  1. Turn the engine switch on (IG).

    Immobiliser: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Immobiliser
    Immobiliser system status / SET or UNSET
    UNSET: Engine switch ON
    SET: Without key
    -

    OK:
    UNSET (Engine switch ON) appears on the screen.



NG
Go to step 34
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

14. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND)

  1. B177523E02
    Disconnect the D7 connector from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D7-8 (STR) - Body ground
    Shift position is P or N
    105 to 115 Ω
    D7-8 (STR) - Body ground
    Shift position is not P nor N
    10 kΩ or higher



NG
Go to step 15
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

15. INSPECT PARK/NEUTRAL POSITION SWITCH

  1. B138018E11
    Disconnect the B5 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    4 - 5
    P
    Below 1 Ω
    4 - 5
    N
    Below 1 Ω
    4 - 5
    Except P and N
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
OK


16. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARK/NEUTRAL POSITION SWITCH)

  1. Measure the resistance according the the value(s) in the table below.B177524E02

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D7-8 (STR) - B5-4
    Always
    Below 1 Ω
    D7-8 (STR) or B5-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (MAIN BODY ECU - PARK/NEUTRAL POSITION SWITCH)
OK


17. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
  1. Disconnect the D55 connector from the ECM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B5-5 - D55-10 (STA)
    Always
    Below 1 Ω
    B5-5 or D55-10 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
OK


18. INSPECT STARTER RELAY

  1. B016200
    Remove the starter relay from engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE STARTER RELAY
OK


19. CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY)
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block starter relay terminal 2 - D55-10 (STA)
    Always
    Below 1 Ω
    Engine room relay block starter relay terminal 2 or D55-10 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STARTER RELAY)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY - BODY GROUND)

20. INSPECT STARTER CUT RELAY

  1. B016200E23
    Remove the starter cut relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block starter relay terminal 2 - D55-10 (STA)
    Always
    Below 1 Ω
    Engine room relay block starter relay terminal 2 or D55-10 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE STARTER CUT RELAY
OK


21. CHECK HARNESS AND CONNECTOR (STARTER CUT RELAY - ECM)
  1. Disconnect the B48 connector from the ECM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block starter cut relay terminal 5 - B48-31 (STAR)
    Always
    Below 1 Ω
    Engine room relay block starter cut relay terminal 5 or B48-31 (STAR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER CUT RELAY - ECM)
OK


22. CHECK HARNESS AND CONNECTOR (STARTER CUT RELAY - MAIN BODY ECU)
  1. Disconnect the D9 connector from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block starter cut relay terminal 5 - D9-6 (STR2)
    Always
    Below 1 Ω
    Engine room relay block starter cut relay terminal 5 or D9-6 (STR2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER CUT RELAY - MAIN BODY ECU)
OK


23. CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY)
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block starter relay terminal 2 - D55-10 (STA)
    Always
    Below 1 Ω
    Engine room relay block starter relay terminal 2 or D55-10 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STARTER RELAY)
OK

REPLACE ECM (Click here)

24. ECU CODE REGISTRATION
  1. Register the ECU code.


NEXT


25. CHECK CRANKING FUNCTION
  1. Check the engine cranking function.

    1. When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch cranks the engine.

      Result:
      Result
      Proceed to
      Engine does not crank
      A
      Engine cranks
      B



B
END (ECU CODE DEFECTIVE)
A


26. REPLACE CERTIFICATION ECU (SMART KEY ECU)
  1. Replace the certification ECU (smart key ECU assembly).


NEXT


27. KEY REGISTRATION
  1. Register the key.


NEXT


28. CHECK CRANKING FUNCTION
  1. Check the engine cranking function.

    1. When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch cranks the engine.

      Result:
      Result
      Proceed to
      Engine does not crank
      A
      Engine cranks
      B



B
END
A

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

29. ECU CODE REGISTRATION
  1. Register the ECU code.


NEXT


30. CHECK CRANKING FUNCTION
  1. Check the engine cranking function.

    1. When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch cranks the engine.

      Result:
      Result
      Proceed to
      Engine does not crank
      A
      Engine cranks
      B



B
END
A


31. REPLACE STEERING LOCK ECU
  1. Replace the steering lock ECU (Click here).


NEXT


32. ECU CODE REGISTRATION
  1. Register the ECU code.


NEXT


33. CHECK CRANKING FUNCTION
  1. Check the engine cranking function.

    1. When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch cranks the engine.

      Result:
      Result
      Proceed to
      Engine does not crank
      A
      Engine cranks
      B



B
END
A

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

34. READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST)
  1. Connect the intelligent tester to the DLC3.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

  1. Turn the engine switch on (IG).

    Smart key: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Start Rqst
    Start request signal response / OK or NG
    OK: Received
    NG: Not received
    -

    OK:
    "OK" (received) and "NG" (not received) appear on the screen.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)


← Engine does not Start (Aug 2008 – Jun 2010)Engine Switch Indicator Circuit (May 2007 – Jul 2008) →