Engine does not Start
Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
| ENGINE START SYSTEM FUNCTION |
If the engine switch is pressed with the shift lever is in the P or N position and the brake pedal depressed, the main body ECU determines that it is an engine start request.
The certification ECU (smart key ECU assembly) and other ECUs perform key verification via the LIN communication line.
The main body ECU activates the ACC relay.
The main body ECU activates the IG1 and IG2 relays.
The certification ECU (smart key ECU assembly) outputs a steering UNLOCK signal. The signal is sent to the main body ECU via the steering lock ECU.
The main body ECU sends an engine start request signal to the ECM.
The ECM sends an ACC cut request signal to the main body ECU.
The ECM and main body ECU activate the starter relay.
The main body ECU deactivates the ACC relay until the main body ECU detects an engine start.
When engine revolution speed reaches 1200 rpm, the ECM determines that the engine has been started.
Symbol of main body ECU
Signal
STP
Stop light switch ON signal
Input
SSW1/SSW2
Engine switch ON signal
Input
ACCD
ACC relay operation signal
Output
SLP
Steering lock actuator position signal
Input
IG1D
IG1 relay operation signal
Output
IG2D
IG2 relay operation signal
Output
STR2
Starter relay operation signal (Sub)
Output
STR
Park/Neutral position switch signal
Input
TACH
Engine start detection signal
Input
STSW
Starter activation request signal
Output
ACCR
ACC cut request signal
Input
Symbol of ECM
Signal
ACCR
ACC cut request signal
Output
TACH
Engine revolution speed signal
Output
STSW
Starter activation request signal
Input
STAR
Starter relay operation signal (Main)
Output
STA
Starter activation signal
Input




WIRING DIAGRAM
See "CRANKING HOLDING FUNCTION CIRCUIT" (Click here).INSPECTION PROCEDURE
| EMERGENCY ENGINE START CONTROL |
If there is a malfunction in the stop light switch circuit or STOP fuse, their signals may not be correctly transmitted to the main body ECU. This may result in the engine not starting even if the engine switch is pressed while the brake pedal is depressed and the shift lever is in the P position.
To activate the starter:Turn the engine switch from off to on (ACC).
Press and hold the engine switch for 15 seconds.
- HINT:
- If the main body ECU is replaced with a new one while the negative (-) battery terminal is connected, the power source mode will be in IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
- After the main body ECU, certification ECU (smart key ECU assembly), steering lock ECU, ID code box (immobiliser code ECU) and/or ECM are/is replaced, perform the registration procedure for the engine immobiliser system.
| 1. CHECK THE ENGINE SWITCH CONDITION |
Check that the power source mode changes.
When the key is inside the vehicle and the shift lever is in the P position, check that the power source mode changes.
- OK:
- off → on (ACC) → on (IG) → off
|
|
||||
| OK | |
| 2. CHECK DTC |
Delete the DTCs (Click here).
Check for DTCs again.
Proceed to the next step based on the inspection result.
- Result:
Result
Proceed to
No DTC is output
A
Smart entry and start system (starting function) DTCs are output
B
Steering lock DTCs are output
C
Engine immobiliser system DTCs are output
D
Vehicle stability control system DTCs are output
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 3. CHECK CRANKING FUNCTION |
Check the engine cranking function.
When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch crank the engine.
- Result:
Result
Proceed to
Engine cranks
A
Engine does not crank
B
|
|
||||
| B | |
| 4. READ VALUE USING INTELLIGENT TESTER (STARTER CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Read the DATA LIST according to the displays on the tester screen.
ECM: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Starter Control
Starter switch signal / ON or OFF
ON: Engine switch on (ST)
OFF: Engine switch except on (ST)
-
- Standard:
Engine switch condition
Tester display
When engine switch is on (ST)
ON
When engine switch is except on (ST)
OFF
|
|
||||
| OK | |
| 5. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STARTER RELAY) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Perform Active Test according to the prompts displayed on the tester.
ECM: Tester Display
Test Part
Control Range
Diagnostic Note
Activate the Starter Relay
Starter
ON or OFF
-
Measure the voltage according to the value(s) in the table below.

- Standard voltage:
Tester Connection
Condition
Specified Condition
Starter relay terminal 2 - Starter relay terminal 1
When starter relay is ON by Active test using intelligent tester
8 to 14 V
Starter relay terminal 2 - Starter relay terminal 1
When starter relay is OFF by Active test using intelligent tester
Below 1 V
|
|
||||
| OK | |
| 6. INSPECT STARTER RELAY |
Remove the starter relay from the engine room relay block.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is applied to terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (STARTER RELAY TERMINAL VOLTAGE AND RESISTANCE) |
Measure the voltage according to the value(s) in the table below.

- Standard voltage:
Tester Connection
Condition
Specified Condition
Starter relay terminal 5 - Body ground
Always
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
Starter relay terminal 1 - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (STARTER RELAY - STARTER) |
Disconnect the B12 connector.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
Engine room relay block starter relay terminal 3 - B12-1
Always
Below 1 Ω
Engine room relay block starter relay terminal 3 or B12-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 9. CHECK HARNESS AND CONNECTOR (BATTERY - STARTER) |
Disconnect the C1 connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
C1-1 - Body ground
Always
11 to 14 V
|
|
||||
| OK | ||
| ||
| 10. READ VALUE USING INTELLIGENT TESTER (PARK/NEUTRAL POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Read the DATA LIST according to the displays on the tester screen.
Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
N SW / C SW
Park/Neutral position switch / ON or OFF
ON: Shift position is P or N
OFF: Shift position is not P or N
-
- OK:
- "ON" (Shift position is P or N) and "OFF" (Shift position is not P or N) appear on the screen.
|
|
||||
| OK | |
| 11. READ VALUE USING INTELLIGENT TESTER (S CODE) |
Connect the intelligent tester to the DLC3.
- HINT:
- When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Turn the engine switch on (IG).
Entry & Start: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
S Code Chk
S code check / OK or NG
OK: Normal
NG: Malfunction
-
- OK:
- "OK" is displayed on the screen.
|
|
||||
| OK | |
| 12. READ VALUE USING INTELLIGENT TESTER (L CODE) |
Connect the intelligent tester to the DLC3.
- HINT:
- When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Turn the engine switch on (IG).
Entry & Start: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
L Code Chk
L code check / OK or NG
OK: Normal
NG: Malfunction
-
- OK:
- "OK" is displayed on the screen.
|
|
||||
| OK | |
| 13. READ VALUE USING INTELLIGENT TESTER (IMMOBILISER SYSTEM STATUS) |
Connect the intelligent tester to the DLC3.
- HINT:
- When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Turn the engine switch on (IG).
Immobiliser: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Immobiliser
Immobiliser system status / SET or UNSET
UNSET: Engine switch ON
SET: Without key
-
- OK:
- UNSET (Engine switch ON) appears on the screen.
|
|
||||
| OK | ||
| ||
| 14. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BODY GROUND) |
Disconnect the D7 connector from the main body ECU.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D7-8 (STA) - Body ground
Shift position is P or N
105 to 115 Ω
D7-8 (STA) - Body ground
Shift position is not P nor N
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 15. INSPECT PARK/NEUTRAL POSITION SWITCH |
Disconnect the B5 connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
4 - 5
P
Below 1 Ω
4 - 5
N
Below 1 Ω
4 - 5
Except P and N
10 kΩ or higher
|
|
||||
| OK | |
| 16. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARK/NEUTRAL POSITION SWITCH) |
Measure the resistance according the the value(s) in the table below.


- Standard resistance:
Tester Connection
Condition
Specified Condition
D7-8 (STR) - B5-4
Always
Below 1 Ω
D7-8 (STA) or B5-4 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 17. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
Disconnect the B3 connector from the ECM.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
B5-5 - B3-11 (STA)
Always
Below 1 Ω
B5-5 or B3-11 (STA) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 18. INSPECT STARTER RELAY |
Remove the starter relay from engine room relay block.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is applied to terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 19. CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY) |
Measure the resistance according to the value(s) in the table below.


- Standard resistance:
Tester Connection
Condition
Specified Condition
Engine room relay block starter relay terminal 2 - B3-11 (STA)
Always
Below 1 Ω
Engine room relay block starter relay terminal 2 or B3-11 (STA) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 20. INSPECT STARTER CUT RELAY |
Remove the starter cut relay from the engine room relay block.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
Engine room relay block starter relay terminal 2 - B3-11 (STA)
Always
Below 1 Ω
Engine room relay block starter relay terminal 2 or B3-11 (STA) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 21. CHECK HARNESS AND CONNECTOR (STARTER CUT RELAY - ECM) |
Disconnect the B2 connector from the ECM.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
Engine room relay block starter cut relay terminal 5 - B2-8 (STAR)
Always
Below 1 Ω
Engine room relay block starter cut relay terminal 5 or B2-8 (STAR) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 22. CHECK HARNESS AND CONNECTOR (STARTER CUT RELAY - MAIN BODY ECU) |
Disconnect the D9 connector from the main body ECU.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
Engine room relay block starter cut relay terminal 5 - D9-6 (STR2)
Always
Below 1 Ω
Engine room relay block starter cut relay terminal 5 or D9-6 (STR2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 23. CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY) |
Measure the resistance according to the value(s) in the table below.


- Standard resistance:
Tester Connection
Condition
Specified Condition
Engine room relay block starter relay terminal 2 - B3-11 (STA)
Always
Below 1 Ω
Engine room relay block starter relay terminal 2 or B3-11 (STA) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 24. ECU CODE REGISTRATION |
Register the ECU code.
| NEXT | |
| 25. CHECK CRANKING FUNCTION |
Check the engine cranking function.
When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch cranks the engine.
- Result:
Result
Proceed to
Engine does not crank
A
Engine cranks
B
|
|
||||
| A | |
| 26. REPLACE CERTIFICATION ECU (SMART KEY ECU) |
Replace the certification ECU (smart key ECU assembly).
| NEXT | |
| 27. KEY REGISTRATION |
Register the key.
| NEXT | |
| 28. CHECK CRANKING FUNCTION |
Check the engine cranking function.
When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch cranks the engine.
- Result:
Result
Proceed to
Engine does not crank
A
Engine cranks
B
|
|
||||
| A | ||
| ||
| 29. ECU CODE REGISTRATION |
Register the ECU code.
| NEXT | |
| 30. CHECK CRANKING FUNCTION |
Check the engine cranking function.
When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch cranks the engine.
- Result:
Result
Proceed to
Engine does not crank
A
Engine cranks
B
|
|
||||
| A | |
| 31. REPLACE STEERING LOCK ECU |
Replace the steering lock ECU (Click here).
| NEXT | |
| 32. ECU CODE REGISTRATION |
Register the ECU code.
| NEXT | |
| 33. CHECK CRANKING FUNCTION |
Check the engine cranking function.
When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch cranks the engine.
- Result:
Result
Proceed to
Engine does not crank
A
Engine cranks
B
|
|
||||
| A | ||
| ||
| 34. READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST) |
Connect the intelligent tester to the DLC3.
- HINT:
- When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Turn the engine switch on (IG).
Smart key: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Start Rqst
Start request signal response / OK or NG
OK: Received
NG: Not received
-
- OK:
- "OK" (received) and "NG" (not received) appear on the screen.
|
|
||||
| OK | ||
| ||
