Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM
SRS Warning Light Remains ON
Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012
DESCRIPTION
The SRS warning light is located on the combination meter assembly. When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to on (IG), and then goes off automatically. If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem. When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light. The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor assembly in case the source voltage drops. When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage. A malfunction in this circuit is not recorded in the center airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal. The signal to illuminate the SRS warning light is transmitted from the center airbag sensor assembly to the combination meter assembly through the CAN communication system. WIRING DIAGRAM
INSPECTION PROCEDURE
1. CHECK SRS WARNING LIGHT OPERATION
Check the SRS warning light operation approximately 6 seconds after the ignition switch is turned on (IG).
Result:
SRS Warning Light Illumination
Proceed to
Remains on
A
Remains on after it goes off
B
B
A
2. CHECK BATTERY VOLTAGE
Measure the voltage of the battery.
Standard voltage:
11 to 14 V
NG
INSPECT CHARGING SYSTEM AND BATTERY
OK
3. CHECK CONNECTOR
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connector is properly connected to the center airbag sensor assembly.
OK:
The connector is properly connected.
HINT:
If the connector is not connected securely, reconnect the connector and proceed to the next inspection.
Disconnect the connector from the center airbag sensor assembly.
Check that the connector terminals are not damaged.
OK:
The terminals are not deformed or damaged.
NG
OK
4. CHECK WIRE HARNESS (CENTER AIRBAG SENSOR ASSEMBLY - BODY GROUND)
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Switch Condition
Specified Condition
D27-21 (IG2) - Body ground
Ignition switch on (IG)
8 to 16 V
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Switch Condition
Specified Condition
D27-25 (E1) - Body ground
Always
Below 1 Ω
D27-26 (E2) - Body ground
Always
Below 1 Ω
NG
OK
5. CHECK SRS WARNING LIGHT
Turn the ignition switch on (IG).
Check the SRS warning light condition.
OK:
After the primary check period, the SRS warning light goes off for approximately 10 seconds and remains on.
HINT:
The primary check is performed for approximately 6 seconds after the ignition switch is turned on (IG).
NG
OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here )
6. CHECK CAN COMMUNICATION SYSTEM
Use the intelligent tester to check if the CAN communication system is functioning normally.
HINT:
Refer to the "Bus Check" of the CAN communication system (Click here ).
The center airbag sensor assembly is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system.
Result:
Result
Proceed to
DTC is not output
A
DTC is output
B
B
A
7. CHECK BATTERY VOLTAGE
Measure the voltage of the battery.
Standard voltage:
11 to 14 V
NG
OK
8. CHECK CONNECTOR
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connector is properly connected to the center airbag sensor assembly.
OK:
The connector is properly connected.
HINT:
If the connector is not connected securely, reconnect the connector and proceed to the next inspection.
Disconnect the connector from the center airbag sensor assembly.
Check that the connector terminals are not damaged.
OK:
The terminals are not deformed or damaged.
NG
OK
9. CHECK WIRE HARNESS (CENTER AIRBAG SENSOR ASSEMBLY - BODY GROUND)
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Switch Condition
Specified Condition
D27-21 (IG2) - Body ground
Ignition switch on (IG)
8 to 16 V
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Switch Condition
Specified Condition
D27-25 (E1) - Body ground
Always
Below 1 Ω
D27-26 (E2) - Body ground
Always
Below 1 Ω
NG
OK
10. CHECK CONNECTOR
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connector is properly connected to the combination meter assembly.
OK:
The connector is properly connected.
HINT:
If the connector is not connected securely, reconnect the connector and proceed to the next inspection.
Disconnect the connector from the combination meter assembly.
Check that the connector terminals are not damaged.
OK:
The terminals are not deformed or damaged.
NG
OK
11. CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)
Disconnect the connector from the combination meter assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Switch Condition
Specified Condition
E1-21 (B) - Body ground
Ignition switch on (IG)
11 to 14 V
E1-22 (B2) - Body ground
Always
11 to 14 V
E1-1 (IG+) - Body ground
Always
11 to 14 V
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Switch Condition
Specified Condition
E1-20 (ES) - Body ground
Always
Below 1 Ω
E1-40 (E2) - Body ground
Always
Below 1 Ω
NG
OK
12. CHECK SRS WARNING LIGHT
Connect the connector to the combination meter assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Check the SRS warning light condition.
OK:
After the primary check period, the SRS warning light goes off for approximately 10 seconds and remains on.
HINT:
The primary check is performed for approximately 6 seconds after the ignition switch is turned on (IG).
NG
OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here )