2007-2013 Highlander Kluger · Service Manual RESTRAINTS

SRS Warning Light Remains ON

Circuit diagnosis · Vehicles built Jul 2010 – Jun 2012

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

The SRS warning light is located on the combination meter assembly.
When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to on (IG), and then goes off automatically.
If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.
When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light.
The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor assembly in case the source voltage drops.
When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.
A malfunction in this circuit is not recorded in the center airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.
The signal to illuminate the SRS warning light is transmitted from the center airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C170104E01

INSPECTION PROCEDURE


1. CHECK SRS WARNING LIGHT OPERATION
  1. Check the SRS warning light operation approximately 6 seconds after the ignition switch is turned on (IG).

    Result:
    SRS Warning Light Illumination
    Proceed to
    Remains on
    A
    Remains on after it goes off
    B



B
Go to step 6
A


2. CHECK BATTERY VOLTAGE
  1. Measure the voltage of the battery.

    Standard voltage:
    11 to 14 V



NG
INSPECT CHARGING SYSTEM AND BATTERY
OK


3. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the center airbag sensor assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check that the connector terminals are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


4. CHECK WIRE HARNESS (CENTER AIRBAG SENSOR ASSEMBLY - BODY GROUND)

  1. C157605E05
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D27-21 (IG2) - Body ground
    Ignition switch on (IG)
    8 to 16 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D27-25 (E1) - Body ground
    Always
    Below 1 Ω
    D27-26 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPLACE WIRE HARNESS
OK


5. CHECK SRS WARNING LIGHT
  1. Turn the ignition switch on (IG).

  1. Check the SRS warning light condition.

    OK:
    After the primary check period, the SRS warning light goes off for approximately 10 seconds and remains on.

    HINT:
    The primary check is performed for approximately 6 seconds after the ignition switch is turned on (IG).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

6. CHECK CAN COMMUNICATION SYSTEM
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    HINT:
    1. Refer to the "Bus Check" of the CAN communication system (Click here).
    2. The center airbag sensor assembly is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


7. CHECK BATTERY VOLTAGE
  1. Measure the voltage of the battery.

    Standard voltage:
    11 to 14 V



NG
CHECK CONNECTOR
OK


8. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the center airbag sensor assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check that the connector terminals are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


9. CHECK WIRE HARNESS (CENTER AIRBAG SENSOR ASSEMBLY - BODY GROUND)

  1. C157605E05
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D27-21 (IG2) - Body ground
    Ignition switch on (IG)
    8 to 16 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D27-25 (E1) - Body ground
    Always
    Below 1 Ω
    D27-26 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPLACE WIRE HARNESS
OK


10. CHECK CONNECTOR
  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the combination meter assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the combination meter assembly.

  1. Check that the connector terminals are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


11. CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

  1. E146920E01
    Disconnect the connector from the combination meter assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-21 (B) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    E1-22 (B2) - Body ground
    Always
    11 to 14 V
    E1-1 (IG+) - Body ground
    Always
    11 to 14 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-20 (ES) - Body ground
    Always
    Below 1 Ω
    E1-40 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPLACE WIRE HARNESS
OK


12. CHECK SRS WARNING LIGHT
  1. Connect the connector to the combination meter assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Check the SRS warning light condition.

    OK:
    After the primary check period, the SRS warning light goes off for approximately 10 seconds and remains on.

    HINT:
    The primary check is performed for approximately 6 seconds after the ignition switch is turned on (IG).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)


← SRS Warning Light Remains ON (Aug 2008 – Jun 2010)SRS Warning Light Remains ON (from Jul 2012) →