2007-2013 Highlander Kluger · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from May 2007


INSPECT STARTER ASSEMBLY

NOTICE:
These tests must be performed within 5 seconds to prevent the coil from burning out.

  1. Perform the pull-in test.

    1. Disconnect the lead wire from terminal C.

    2. A133512E02
      Connect the battery to the magnetic switch as shown in the illustration. Check that the clutch pinion gear extends.
      If the clutch pinion gear does not move, replace the repair service starter kit.

  1. A133513E02
    Perform the hold-in test.

    1. Maintain the battery connections of the pull-in test above, but disconnect the negative (-) lead from terminal C. Check that the pinion gear remains extended.
      If the clutch pinion gear returns inward, replace the repair service starter kit.

  1. A133514E02
    Perform the clutch pinion gear return test.

    1. Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns.
      If the clutch pinion gear does not return, replace the repair service starter kit.

  1. A133510E02
    Perform the no-load performance test.

    1. Connect the lead wire to terminal C with the nut. Make sure that the lead is not grounded.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    2. Clamp the starter in a vise.

    3. Connect the battery and an ammeter to the starter as shown in the illustration.

    4. Check that the starter rotates smoothly and steadily with the clutch pinion gear extended. Check that the ammeter reads the current specified below.

      Standard current:
      Tester Connection
      Condition
      Specified Condition
      Battery positive terminal - Terminal 30 - Terminal 50
      11.5 V
      90 A or less

      If the result is not as specified, overhaul the starter assembly.


INSPECT REPAIR SERVICE STARTER KIT

  1. A058586
    Check the plunger.

    1. Push in the plunger and check that it returns quickly to its original position.
      If necessary, replace the repair service starter kit.

  1. A079725E12
    Check if the pull-in coil has an open circuit.

    1. Using an ohmmeter, measure the resistance between terminals 50 and C.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Terminal C
      -
      Below 1 Ω

      If the result is not as specified, replace the repair service starter kit.

  1. A079726E10
    Check if the hold-in coil has an open circuit.

    1. Using an ohmmeter, measure the resistance between terminal 50 and the switch body.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      -
      Below 2 Ω

      If the result is not as specified, replace the repair service starter kit.


INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the commutator surface for dirt or burning.
    If the surface is dirty or burnt, smooth the surface with 400-grit sandpaper or leather.

  1. A058372E07
    Check if the commutator has an open circuit.

    1. Using an ohmmeter, measure the resistance between any 2 segments of the commutator.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      -
      Below 1 Ω

      If the result is not as specified, replace the armature assembly.

    2. A058373E05
      Using an ohmmeter measure the resistance between each segment of the commutator and armature coil core.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Commutator - Coil core
      -
      10 kΩ or higher

      If the result is not as specified, replace the armature assembly.

  1. A058584E01
    Using a vernier caliper, measure the commutator's length.

    Standard length:
    3.1 to 3.8 mm (0.122 to 0.150 in.)

    If the length is greater than the maximum, replace the starter armature assembly.


INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY

  1. A076677E01
    Using a vernier caliper, measure the brush length.

    Standard length:
    4.0 to 9.0 mm (0.158 to 0.354 in.)

    If the length is less than the minimum, replace the starter commutator end frame assembly.

  1. A079766
    Check the brush insulation.

    1. Using a ohmmeter, measure the resistance between the positive (+) and negative (-) brushes.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Positive (+) brush - Negative (-) brush
      -
      10 kΩ or higher

      If the result is not as specified, repair or replace the starter commutator end frame assembly.


INSPECT STARTER CLUTCH

  1. A081655E01
    Rotate the clutch pinion gear counterclockwise and check that it turns freely. Try to rotate the clutch pinion gear clockwise and check that it locks.
    If necessary, replace the motor terminal starter kit.

← DISASSEMBLY (from May 2007)REASSEMBLY (from May 2007) →