B1603/83 Front Satellite Sensor Bus RH Initialization Incomplete
Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010
Also covers:
- B1612/83 Lost Communication with Front Airbag Sensor RH
- B1613/83 Front Airbag Sensor RH Initialization Incomplete
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The front airbag sensor RH circuit consists of the center airbag sensor assembly and front airbag sensor RH.The front airbag sensor RH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1603/83, B1612/83 or B1613/83 is recorded when a malfunction is detected in the front airbag sensor RH circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1603/83 B1612/83 B1613/83 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.
- OK:
- The connectors are properly connected.
- HINT:
- If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.
Check that the connector terminals are not damaged.
- OK:
- The terminals are not deformed or damaged.
|
|
||||
| OK | |
| 2. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN) |
Connect the connectors that link the engine room main wire and instrument panel wire.

Using SST, connect terminals 29 (+SR) and 27 (-SR) of connector B.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting.
- SST
- 09843-18040
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
A34-2 (+SR) - A34-1 (-SR)
Always
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT) |
Disconnect SST from connector B.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
A34-2 (+SR) - A34-1 (-SR)
Always
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO B+) |
Connect the negative (-) terminal cable to the battery.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
A34-2 (+SR) - Body ground
Ignition switch on (IG)
Below 1 V
A34-1 (-SR) - Body ground
Ignition switch on (IG)
Below 1 V
|
|
||||
| OK | |
| 5. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND) |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
A34-2 (+SR) - Body ground
Always
1 MΩ or higher
A34-1 (-SR) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 6. CHECK FRONT AIRBAG SENSOR RH |
Connect the connector to the center airbag sensor assembly.

Interchange the front airbag sensor LH with RH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result
Proceed to
DTC B1603/83, B1612/83, B1613/83, B1608/84, B1617/84 and B1618/84 are not output
A
DTC B1608/84, B1617/84 and B1618/84 are output
B
DTC B1603/83, B1612/83 and B1613/83 are output
C
- HINT:
- Codes other than B1603/83, B1612/83, B1613/83, B1608/84, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | ||
| ||
| 7. CHECK INSTRUMENT PANEL WIRE (OPEN) |
Disconnect the instrument panel wire connector from the engine room main wire.

- HINT:
- SST has already been inserted into connector B.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
AD1-2 (-SR) - AD1-1 (+SR)
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 8. CHECK INSTRUMENT PANEL WIRE (SHORT) |
Disconnect the instrument panel wire connector from the engine room main wire.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
AD1-2 (-SR) - AD1-1 (+SR)
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 9. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+) |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the instrument panel wire connector from the engine room main wire.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
AD1-2 (-SR) - Body ground
Ignition switch on (IG)
Below 1 V
AD1-1 (+SR) - Body ground
Ignition switch on (IG)
Below 1 V
|
|
||||
| OK | ||
| ||
| 10. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND) |
Disconnect the instrument panel wire connector from the engine room main wire.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
AD1-2 (-SR) - Body ground
Always
1 MΩ or higher
AD1-1 (+SR) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||
