B1608/84 Front Satellite Sensor Bus LH Initialization Incomplete
Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008
Also covers:
- B1617/84 Lost Communication with Front Airbag Sensor LH
- B1618/84 Front Airbag Sensor LH Initialization Incomplete
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The front airbag sensor LH circuit consists of the center airbag sensor assembly and front airbag sensor LH.The front airbag sensor LH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1608/84, B1617/84 or B1618/84 is recorded when a malfunction is detected in the front airbag sensor LH circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1608/84 B1617/84 B1618/84 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.
- OK:
- The connectors are properly connected.
- HINT:
- If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.
Check that the connector terminals are not damaged.
- OK:
- The terminals are not deformed or damaged.
|
|
||||
| OK | |
| 2. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN) |
Connect the terminals that link the engine room main wire and instrument panel wire.

Using SST, connect terminals 30 (+SL) and 28 (-SL) of connector B.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting.
- SST
- 09843-18040
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
A4-2 (+SL) - A4-1 (-SL)
Always
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT) |
Disconnect SST from connector B.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
A4-2 (+SL) - A4-1 (-SL)
Always
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+) |
Connect the negative (-) terminal cable to the battery.

Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
A4-2 (+SL) - Body ground
Ignition switch on (IG)
Below 1 V
A4-1 (-SL) - Body ground
Ignition switch on (IG)
Below 1 V
|
|
||||
| OK | |
| 5. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND) |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
A4-2 (+SL) - Body ground
Always
1 MΩ or higher
A4-1 (-SL) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 6. CHECK FRONT AIRBAG SENSOR LH |
Connect the connector to the center airbag sensor assembly.

Interchange the front airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result
Proceed to
DTCs B1608/84, B1617/84, B1618/84, B1603/83, B1612/83 and B1613/83 are not output
A
DTC B1608/84, B1617/84 and B1618/84 are output
B
DTC B1603/83, B1612/83 and B1613/83 are output
C
- HINT:
- Codes other than DTCs B1608/84, B1617/84, B1618/84, B1603/83, B1612/83 and B1613/83, may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| A | ||
| ||
| 7. CHECK INSTRUMENT PANEL WIRE (OPEN) |
Disconnect the instrument panel wire connector from the engine room main wire.

- HINT:
- SST has already been inserted into connector B.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
AD6-1 (+SL) - AD6-2 (-SL)
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 8. CHECK INSTRUMENT PANEL WIRE (SHORT) |
Disconnect the instrument panel wire connector from the engine room main wire.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
AD6-1 (+SL) - AD6-2 (-SL)
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||
| 9. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+) |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the instrument panel wire connector from the engine room main wire.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
AD6-1 (+SL) - Body ground
Ignition switch on (IG)
Below 1 V
AD6-2 (-SL) - Body ground
Ignition switch on (IG)
Below 1 V
|
|
||||
| OK | ||
| ||
| 10. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND) |
Disconnect the instrument panel wire connector from the engine room main wire.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
AD6-1 (+SL) - Body ground
Always
1 MΩ or higher
AD6-2 (-SL) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | ||
| ||
