2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1608/84 Front Satellite Sensor Bus LH Initialization Incomplete

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The front airbag sensor LH circuit consists of the center airbag sensor assembly and front airbag sensor LH.
The front airbag sensor LH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1608/84, B1617/84 or B1618/84 is recorded when a malfunction is detected in the front airbag sensor LH circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1608/84
B1617/84
B1618/84
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.
  2. Front airbag sensor LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Engine room main wire
  3. Front airbag sensor LH
  4. Center airbag sensor assembly

WIRING DIAGRAM

C145438E06

INSPECTION PROCEDURE


1. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly and the front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.

  1. Check that the connector terminals are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (OPEN)

  1. C145443E05
    Connect the terminals that link the engine room main wire and instrument panel wire.

  1. Using SST, connect terminals 30 (+SL) and 28 (-SL) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 (+SL) - A4-1 (-SL)
    Always
    Below 1 Ω



NG
Go to step 7
OK


3. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT)

  1. C145444E06
    Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 (+SL) - A4-1 (-SL)
    Always
    1 MΩ or higher



NG
Go to step 8
OK


4. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO B+)

  1. C145444E06
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 (+SL) - Body ground
    Ignition switch on (IG)
    Below 1 V
    A4-1 (-SL) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
Go to step 9
OK


5. CHECK FRONT AIRBAG SENSOR LH CIRCUIT (SHORT TO GROUND)

  1. C145444E06
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 (+SL) - Body ground
    Always
    1 MΩ or higher
    A4-1 (-SL) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 10
OK


6. CHECK FRONT AIRBAG SENSOR LH

  1. C123723E05
    Connect the connector to the center airbag sensor assembly.

  1. Interchange the front airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1608/84, B1617/84, B1618/84, B1603/83, B1612/83 and B1613/83 are not output
    A
    DTC B1608/84, B1617/84 and B1618/84 are output
    B
    DTC B1603/83, B1612/83 and B1613/83 are output
    C

    HINT:
    Codes other than DTCs B1608/84, B1617/84, B1618/84, B1603/83, B1612/83 and B1613/83, may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE FRONT AIRBAG SENSOR LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

7. CHECK INSTRUMENT PANEL WIRE (OPEN)

  1. C145447E05
    Disconnect the instrument panel wire connector from the engine room main wire.

    HINT:
    SST has already been inserted into connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    AD6-1 (+SL) - AD6-2 (-SL)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE

8. CHECK INSTRUMENT PANEL WIRE (SHORT)

  1. C145448E06
    Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    AD6-1 (+SL) - AD6-2 (-SL)
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE

9. CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

  1. C145448E06
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the instrument panel wire connector from the engine room main wire.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    AD6-1 (+SL) - Body ground
    Ignition switch on (IG)
    Below 1 V
    AD6-2 (-SL) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE

10. CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

  1. C145448E06
    Disconnect the instrument panel wire connector from the engine room main wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    AD6-1 (+SL) - Body ground
    Always
    1 MΩ or higher
    AD6-2 (-SL) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE ENGINE ROOM MAIN WIRE


← B1608/84 Front Satellite Sensor Bus LH Initialization Incomplete (+ B1617/84, B1618/84) (May 2007 – Jul 2008)B1608/84 Front Satellite Sensor Bus LH Initialization Incomplete (+ B1617/84, B1618/84) (from Jul 2010) →