2007-2013 Highlander Kluger · Service Manual BRAKE

DISASSEMBLY

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

HINT:
  1. Use the same procedures for the RH side and the LH side.
  2. The procedures listed below are for the LH side.


1. REMOVE REAR WHEEL

2. REMOVE REAR AXLE SHAFT NUT (for 4WD)

NOTICE:
Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

HINT:
Click here.


3. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for 2WD)

  1. C167785
    Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.


4. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for 4WD)

  1. C165996
    Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.


5. REMOVE REAR DISC

  1. C166438E01
    Put matchmarks on the rear disc and the axle hub.

  1. D028126
    Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.


6. REMOVE NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING

  1. C166147
    Remove the 2 No. 1 parking brake shoe return tension springs.


7. SEPARATE NO. 1 PARKING BRAKE SHOE ASSEMBLY

  1. C166148
    Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 1 parking brake shoe assembly from the backing plate.


8. REMOVE PARKING BRAKE SHOE STRUT

  1. C166149
    Remove the parking brake shoe strut and the parking brake shoe strut compression spring.


9. SEPARATE NO. 2 PARKING BRAKE SHOE ASSEMBLY

  1. C166150
    Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 2 parking brake shoe assembly from the backing plate.


10. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET

  1. C166151
    Remove the parking brake shoe adjusting screw set.


11. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY

  1. C166152
    Separate the No. 2 parking brake shoe return tension spring and remove the No. 1 parking brake shoe assembly.


12. REMOVE NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING

  1. C166153
    Remove the No. 2 parking brake shoe return tension spring from the No. 2 parking brake shoe assembly.


13. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER

  1. C166154
    Using needle-nose pliers, separate the No. 3 parking brake cable assembly from the parking brake shoe lever as shown in the illustration.

    NOTICE:
    Be careful not to damage the No. 3 parking brake cable assembly.


14. REMOVE PARKING BRAKE SHOE LEVER

  1. C166161
    Remove the C-washer, shim and the parking brake shoe lever from the No. 2 parking brake shoe assembly.


15. REMOVE PARKING BRAKE SHOE GUIDE PLATE SET BOLT

  1. C166163
    Remove the parking brake shoe guide plate set bolt and the parking brake shoe guide plate.


16. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD)

  1. C168092
    Remove the No. 1 parking brake shoe hold down spring pin.


17. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD)

  1. C166157
    Remove the No. 2 parking brake shoe hold down spring pin.


18. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 2WD)

NOTICE:
Perform this procedure only when the No. 2 parking brake shoe hold down spring pin is replaced.

HINT:
Click here.


19. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 4WD)

NOTICE:
Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

HINT:
Click here.


20. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD)

  1. C168093
    Remove the No. 2 parking brake shoe hold down spring pin.


21. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD)

  1. C168096
    Remove the No. 1 parking brake shoe hold down spring pin.

← DISASSEMBLY (Aug 2008 – Jun 2010)INSPECTION (from May 2007) →