2007-2013 Highlander Kluger · Service Manual BRAKE

REASSEMBLY

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

NOTICE:
Before installation, apply high temperature grease to the parts indicated by arrows (Click here).


1. INSTALL NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD)

  1. C168093
    Install the No. 2 parking brake shoe hold down spring pin.


2. INSTALL NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD)

  1. C168096
    Install the No. 1 parking brake shoe hold down spring pin.


3. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY (for 2WD)

NOTICE:
Perform this procedure only when the No. 2 parking brake shoe hold down spring pin is replaced.

HINT:
Click here.


4. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY (for 4WD)

NOTICE:
Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

HINT:
Click here.


5. INSTALL NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD)

  1. C168092
    Install the No. 1 parking brake shoe hold down spring pin.


6. INSTALL NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD)

  1. C166157
    Install the No. 2 parking brake shoe hold down spring pin.


7. APPLY HIGH TEMPERATURE GREASE
  1. Apply high temperature grease to the backing plate which makes contact with the shoe.


8. INSTALL PARKING BRAKE SHOE GUIDE PLATE SET BOLT
  1. Apply adhesive to the threads of the parking brake shoe guide plate set bolt.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. C166163
    Install the parking brake shoe guide plate and the parking brake shoe guide plate set bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


9. INSTALL PARKING BRAKE SHOE LEVER
  1. Apply high temperature grease to the parking brake shoe lever which makes contact with the No. 2 parking brake shoe assembly.

  1. C166162
    Install the parking brake shoe lever and shim to the No. 2 parking brake shoe assembly with a new C-washer.

  1. C132648
    Using a feeler gauge, measure the clearance between the No. 2 parking brake shoe assembly and parking brake shoe lever.

    Standard clearance:
    Less than 0.35 mm (0.014 in.)

    If the clearance is not as specified, replace the shim with one of the appropriate size.
    Part No.
    Shim Thickness
    90564-09184
    0.3 mm (0.012 in.)
    90564-09185
    0.6 mm (0.024 in.)
    90564-09186
    0.9 mm (0.035 in.)


10. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER

  1. C166155
    Using needle-nose pliers, connect the No. 3 parking brake cable assembly to the parking brake shoe lever as shown in the illustration.


11. INSTALL NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING

  1. C166153
    Install the No. 2 parking brake shoe return tension spring to the No. 2 parking brake shoe assembly.


12. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY

  1. C166152
    Connect the No. 2 parking brake shoe return tension spring to install the No. 1 parking brake shoe assembly.


13. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET

  1. C132649
    Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.

  1. C166151
    Install the parking brake shoe adjusting screw set.


14. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY

  1. C166150
    Install the No. 2 parking brake shoe assembly to the backing plate with the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring, and No. 2 parking brake shoe hold down spring cup.


15. INSTALL PARKING BRAKE SHOE STRUT

  1. C166149
    Install the parking brake shoe strut and the parking brake shoe strut compression spring.


16. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY

  1. C166148
    Install the No. 1 parking brake shoe assembly to the backing plate with the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring, and No. 2 parking brake shoe hold down spring cup.


17. INSTALL NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING

  1. C166147
    Install the 2 No. 1 parking brake shoe return tension springs.

    HINT:
    First install the front side spring and then the rear side spring.


18. CHECK PARKING BRAKE INSTALLATION

  1. Check that each part is installed properly.

    C166165E01

    NOTICE:
    There should be no oil or grease on the friction surface of the shoe lining and disc.


19. INSTALL REAR DISC

  1. C166438E01
    Align matchmarks and install the rear disc.

    NOTICE:
    When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.


20. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY (for 2WD)

  1. C167785
    Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 57 ft.*lbf }


21. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY (for 4WD)

  1. C165996
    Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 57 ft.*lbf }


22. INSTALL REAR AXLE SHAFT NUT (for 4WD)

NOTICE:
Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

HINT:
Click here.


23. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for LHD)
  1. Remove the driver side knee airbag assembly (Click here).

  1. Completely release the parking brake pedal.

  1. C166160E01
    Loosen the lock nut and the adjusting nut to completely release the parking brake cable.

  1. Remove the rear wheel.

  1. Temporarily install the hub nuts.

  1. Remove the shoe adjusting hole plug.

  1. C131914E01
    Turn the shoe adjuster and expand the shoe until the disc locks.

  1. Turn and contract the shoe adjuster until the disc can rotate smoothly.

    Standard:
    Return 8 notches.

  1. Check that there is no brake drag against the shoe.

  1. Install the shoe adjusting hole plug.

  1. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

    Parking brake pedal travel:
    8 to 10 notches at 300 N (31 kgf, 67 lbf)

  1. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

  1. Check that there is no brake drag against the shoe.

  1. Remove the hub nuts.

  1. Install the rear wheel.

    Torque:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

  1. Install the driver side knee airbag assembly (Click here).


24. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for RHD)
  1. Remove the driver side knee airbag assembly (Click here).

  1. Completely release the parking brake pedal.

  1. C165692E01
    Loosen the lock nut and adjusting nut to completely release the parking brake cable.

  1. Remove the rear wheel.

  1. Temporarily install the hub nuts.

  1. Remove the shoe adjusting hole plug.

  1. C131914E01
    Turn the shoe adjuster and expand the shoe until the disc locks.

  1. Turn and contract the shoe adjuster until the disc can rotate smoothly.

    Standard:
    Return 8 notches.

  1. Check that there is no brake drag against the shoe.

  1. Install the shoe adjusting hole plug.

  1. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

    Parking brake pedal travel:
    8 to 10 notches at 300 N (31 kgf, 67 lbf)

  1. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

  1. Check that there is no brake drag against the shoe.

  1. Remove the hub nuts.

  1. Install the rear wheel.

    Torque:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

  1. Install the driver side knee airbag assembly (Click here).


25. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

← REASSEMBLY (Aug 2008 – Jun 2010)PRECAUTION (May 2007 – Jul 2008) →