2007-2013 Highlander Kluger · Service Manual BODY

Driver Side Power Window does not Operate with Power Window Master Switch

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

If the manual UP/DOWN and AUTO DOWN functions do not operate, a malfunction may exist in the power window master switch, power window regulator motor or wire harness.

WIRING DIAGRAM

B175980E05
B175980E06

INSPECTION PROCEDURE


1. INSPECT POWER WINDOW MASTER SWITCH (DRIVER SWITCH)

  1. B164359E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    8 (U) - 1 (E) - 4 (A)
    Auto UP
    Below 1 Ω
    8 (U) - 1 (E)
    Manual UP
    Below 1 Ω
    5 (D) - 1 (E)
    Manual DOWN
    Below 1 Ω
    4 (A) - 5 (D) - 1 (E)
    Auto DOWN
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    1 (U) - 9 (E) - 4 (A)
    Auto UP
    Below 1 Ω
    1 (U) - 9 (E)
    Manual UP
    Below 1 Ω
    5 (D) - 9 (E)
    Manual DOWN
    Below 1 Ω
    4 (A) - 5 (D) - 9 (E)
    Auto DOWN
    Below 1 Ω



NG
REPLACE POWER WINDOW MASTER SWITCH (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - MOTOR (DRIVER SIDE))

  1. for LHD:

    1. B175976E11
      Disconnect the M1 and H1 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M1-8 (U) - H1-10 (UP1)
      Always
      Below 1 Ω
      M1-4 (A) - H1-4 (AUTO)
      Always
      Below 1 Ω
      M1-5 (D) - H1-7 (DWN1)
      Always
      Below 1 Ω
      M1-8 (U) - Body ground
      Always
      10 kΩ or higher
      M1-4 (A) - Body ground
      Always
      10 kΩ or higher
      M1-5 (D) - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. B175976E12
      Disconnect the L1 and G10 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      L1-1 (U) - G10-10 (UP1)
      Always
      Below 1 Ω
      L1-4 (A) - G10-4 (AUTO)
      Always
      Below 1 Ω
      L1-5 (D) - G10-7 (DWN1)
      Always
      Below 1 Ω
      L1-1 (U) - Body ground
      Always
      10 kΩ or higher
      L1-4 (A) - Body ground
      Always
      10 kΩ or higher
      L1-5 (D) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER SIDE)

  1. Remove the power window regulator motor assembly (Click here).B172246E01

    1. Apply battery voltage to the motor connector according to the table below.

      NOTICE:
      Do not apply battery voltage to any terminals except terminals 1, 2, 4, 7, 9 and 10.

      OK:
      Switch Condition
      Measurement Condition
      Specified Condition
      Manual Operation
      Battery positive (+) → Terminal 2 (B), 9 (LIN)
      Battery negative (-) → Terminal 1 (E), 7 (DWN1)
      Motor gear rotates counterclockwise
      Battery positive (+) → Terminal 2 (B), 9 (LIN)
      Battery negative (-) → Terminal 1 (E), 10 (UP1)
      Motor gear rotates clockwise
      Auto Operation
      Battery positive (+) → Terminal 2 (B), 9 (LIN)
      Battery negative (-) → Terminal 1 (E), 4 (AUTO), 7 (DWN1)
      Motor gear rotates counterclockwise
      Battery positive (+) → Terminal 2 (B), 9 (LIN)
      Battery negative (-) → Terminal 1 (E), 4 (AUTO), 10 (UP1)
      Motor gear rotates clockwise



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side) (Click here)
OK

REPLACE POWER WINDOW MASTER SWITCH (Click here)


← Driver Side Power Window does not Operate with Power Window Master Switch (May 2007 – Jul 2008)Driver Side Power Window does not Operate with Power Window Master Switch (from Jul 2010) →