2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

DTC CHECK / CLEAR

Troubleshooting · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

HINT:
  1. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
  2. If the system cannot enter the diagnostic mode, refer to the AVC-LAN circuit (Click here).
  3. After the ignition switch is turned on (IG), check that the map is displayed before starting the diagnostic mode. Otherwise, some items cannot be checked.


START DIAGNOSTIC MODE
  1. There are 2 methods to start diagnostic mode. Start the mode by using one of them.

  2. E150769E03
    Method 1

    1. Start the engine.

    2. While pressing and holding the "INFO" switch, operate the light control switch: OFF → Turn ON → Turn OFF → Turn ON → Turn OFF → Turn ON → Turn OFF.

    3. The diagnostic mode starts and the "System Check Mode" screen will be displayed. Service inspection starts automatically and the result will be displayed.

  3. Method 2

    1. Start the engine.

    2. E150769E04
      Press the "DISP" switch.

    3. E109432E12
      From the display quality adjustment screen, touch the corners of the screen in the following order: upper left → lower left → upper left → lower left → upper left → lower left.

    4. The diagnostic mode starts and the "System Check Mode" screen will be displayed. Service inspection starts automatically and the result will be displayed.


FINISH DIAGNOSTIC MODE
  1. There are 2 methods to end diagnostic mode. Use one of them.

    1. Turn the ignition switch off.

    2. Press and hold the "DISP" switch for 3 seconds.


DIAGNOSIS MENU

  1. E136185E07
    The "Diagnosis MENU" screen will be displayed by pressing the "Menu" switch on the "System Check Mode" screen.


CHECK DTC

  1. E136186E06
    Read the system check result.

    1. If the check result is "EXCH", "CHEK" or "Old", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

      HINT:
      1. If all check results are "OK", go to communication DTC check.
      2. If a device name is not known, its physical address is displayed.

      HINT:
      When proceeding to view the results of another device, press the "Service" switch to return to the "System Check Mode" screen. Repeat this step.

  2. E136187E02
    Read the communication diagnostic check result.

    1. Return to the "System Check Mode" screen, and press the "LAN Mon" switch to enter the "LAN Monitor" screen.

    2. E136196E01
      If the check result is "CHEK" or "Old", touch the displayed check result to view the results on the individual communication diagnostic screen and record them.

      HINT:
      1. If all check results are "No Err", the system judges that no DTC exists.
      2. The sub-code (relevant device) will be indicated by its physical address.
      3. When proceeding to view the results of another device, press the "Service" switch to return to the original "LAN Monitor" screen. Repeat this step.


DTC CLEAR/RECHECK

  1. E136190E02
    Clear DTC

    1. Press the "Code CLR" switch for 3 seconds.

    2. The check results are cleared.

  2. E136191E02
    Recheck

    1. Press the "Recheck" switch.

    2. E136192E04
      Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

    3. E136192E05
      Press the "LAN Mon" switch to change to the "LAN Monitor" screen.

    4. E136193E02
      Confirm that all diagnostic codes are "No Err". If a code other than "No Err" is displayed, troubleshoot again.

← TERMINALS OF ECU (from Jul 2012)DTC CHECK / CLEAR (Aug 2008 – Jun 2010) →