INSTALLATION
Removal / installation · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| 1.
INSTALL REAR LOWER COIL SPRING INSULATOR |
 |
- Install the rear lower coil spring insulator onto the rear shock absorber assembly.
- NOTICE:
- Fit the recessed part of the rear lower coil spring insulator into the recession on the shock absorber assembly.
| 2.
INSTALL REAR NO. 1 SPRING BUMPER |
 |
- Install the rear No. 1 spring bumper to the rear shock absorber assembly.
| 3.
TEMPORARILY INSTALL REAR COIL SPRING |
 |
- Attach SST to the rear coil spring and secure it in a vise.
- SST
- 09727-30021
(09727-00010, 09727-00021, 09727-00031)
- Attach the arm of SST to the diameter of the rear coil spring.
- CAUTION:
- Make sure that the rear coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.
- Make sure that the claws of the hooks are securely attached.
Using SST, compress the rear coil spring.
- CAUTION:
- If the rear coil spring bends during the compression, immediately stop the compression and reinstall SST.
- Do not compress the spring until the coil springs contact each other.
- Do not use an impact wrench. It will damage SST.
- Temporarily install the rear coil spring together with SST to the rear shock absorber assembly.
| 4.
INSTALL REAR SUSPENSION SUPPORT ASSEMBLY |
 |
- Install the rear suspension support assembly to the rear shock absorber assembly.
- HINT:
- Align the cutout on the rear shock absorber assembly with the protrusion on the rear suspension support assembly by referring to the illustration.
| 5.
INSTALL REAR SUPPORT TO REAR SHOCK ABSORBER COLLAR |
 |
- Install the rear support to rear shock absorber collar to the rear shock absorber assembly.
| 6.
TEMPORARILY INSTALL REAR SUPPORT TO REAR SHOCK ABSORBER NUT |
 |
- Temporarily install the rear support to rear shock absorber nut to the rear shock absorber assembly.
| 7.
INSTALL REAR COIL SPRING |
 |
- Install the rear coil spring.
- CAUTION:
- Do not use an impact wrench. It will damage the SST.
- NOTICE:
- Make sure that the end of the rear coil spring is positioned in the depression of the rear lower coil spring insulator.
- Ensure that the stud bolt is positioned 3.5° to the outside of the vehicle as shown in the illustration. The deviation should be within +-5°.
| 8.
INSTALL REAR SHOCK ABSORBER WITH COIL SPRING (for 2WD) |
 |
- Install the rear shock absorber with coil spring with the 3 nuts.
-
Torque:
- 58 N*m{
591 kgf*cm
, 43 ft.*lbf
}
- Install the rear shock absorber with coil spring with the 2 bolts and 2 nuts.
-
Torque:
- 290 N*m{
2956 kgf*cm
, 213 ft.*lbf
}
- NOTICE:
- When installing the nuts, keep the bolts from rotating.
- Fully tighten the rear support to rear shock absorber nut.
-
Torque:
- 55 N*m{
561 kgf*cm
, 40 ft.*lbf
}
| 9.
INSTALL REAR SHOCK ABSORBER WITH COIL SPRING (for 4WD) |
 |
- Install the rear shock absorber with coil spring with the 3 nuts.
-
Torque:
- 58 N*m{
591 kgf*cm
, 43 ft.*lbf
}
- Install the rear shock absorber with coil spring with the 2 bolts and 2 nuts.
-
Torque:
- 290 N*m{
2956 kgf*cm
, 213 ft.*lbf
}
- NOTICE:
- When installing the nuts, keep the bolts from rotating.
- Fully tighten the rear support to rear shock absorber nut.
-
Torque:
- 55 N*m{
561 kgf*cm
, 40 ft.*lbf
}
| 10.
INSTALL REAR NO. 1 SUSPENSION SUPPORT COVER |
 |
- Install the rear No. 1 suspension support cover.
| 11.
INSTALL REAR STABILIZER LINK ASSEMBLY (for 2WD) |
 |
- Install the rear stabilizer link assembly to the rear shock absorber with coil spring with the nut.
-
Torque:
- 39 N*m{
400 kgf*cm
, 29 ft.*lbf
}
- HINT:
- If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.
| 12.
INSTALL REAR STABILIZER LINK ASSEMBLY (for 4WD) |
 |
- Install the rear stabilizer link assembly to the rear shock absorber with coil spring with the nut.
-
Torque:
- 39 N*m{
400 kgf*cm
, 29 ft.*lbf
}
- HINT:
- If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.
| 13.
INSTALL REAR SPEED SENSOR WIRE (for 2WD) |
 |
- Install the rear speed sensor wire to the rear shock absorber with coil spring with the bolt.
-
Torque:
- 5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
- NOTICE:
- Do not twist the rear speed sensor wire when installing it.
| 14.
INSTALL REAR SPEED SENSOR (for 4WD) |
 |
- Install the rear speed sensor to the rear shock absorber with coil spring with the bolt.
-
Torque:
- 5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
- NOTICE:
- Do not twist the rear speed sensor wire when installing it.
| 15.
INSTALL REAR FLEXIBLE HOSE (for 2WD) |
 |
- Install the rear flexible hose to the rear shock absorber with coil spring with the bolt.
-
Torque:
- 19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
- NOTICE:
- Do not twist the rear flexible hose when installing it.
| 16.
INSTALL REAR FLEXIBLE HOSE (for 4WD) |
 |
- Install the rear flexible hose to the rear shock absorber with coil spring with the bolt.
-
Torque:
- 19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
- NOTICE:
- Do not twist the rear flexible hose when installing it.
| 17.
INSTALL DECK SIDE TRIM
|
 |
- Engage the 3 guides and 4 claws as shown in the illustration.
- Install the deck side trim LH with the bolt.
| 18.
INSTALL DECK SIDE TRIM COVER
|
 |
- Engage the 2 claws and install the deck side trim cover LH.
| 19.
INSTALL REAR WHEEL |
 |
-
Torque:
- 103 N*m{
1050 kgf*cm
, 76 ft.*lbf
}
| 20.
INSPECT AND ADJUST REAR WHEEL ALIGNMENT |
 |
- HINT:
-
Click here