2007-2013 Highlander Kluger · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL REAR LOWER COIL SPRING INSULATOR

  1. C166023E01
    Install the rear lower coil spring insulator onto the rear shock absorber assembly.

    NOTICE:
    Fit the recessed part of the rear lower coil spring insulator into the recession on the shock absorber assembly.


2. INSTALL REAR NO. 1 SPRING BUMPER

  1. C166020
    Install the rear No. 1 spring bumper to the rear shock absorber assembly.


3. TEMPORARILY INSTALL REAR COIL SPRING

  1. C265188E02
    Attach SST to the rear coil spring and secure it in a vise.
    SST
    09727-30021   (09727-00010, 09727-00021, 09727-00031)

  1. C263591
    Attach the arm of SST to the diameter of the rear coil spring.

    CAUTION:
    1. Make sure that the rear coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.
    2. Make sure that the claws of the hooks are securely attached.

  1. Using SST, compress the rear coil spring.

    CAUTION:
    1. If the rear coil spring bends during the compression, immediately stop the compression and reinstall SST.
    2. Do not compress the spring until the coil springs contact each other.
    3. Do not use an impact wrench. It will damage SST.

  1. C271922
    Temporarily install the rear coil spring together with SST to the rear shock absorber assembly.


4. INSTALL REAR SUSPENSION SUPPORT ASSEMBLY

  1. C271923E01
    Install the rear suspension support assembly to the rear shock absorber assembly.

    HINT:
    Align the cutout on the rear shock absorber assembly with the protrusion on the rear suspension support assembly by referring to the illustration.


5. INSTALL REAR SUPPORT TO REAR SHOCK ABSORBER COLLAR

  1. C271920
    Install the rear support to rear shock absorber collar to the rear shock absorber assembly.


6. TEMPORARILY INSTALL REAR SUPPORT TO REAR SHOCK ABSORBER NUT

  1. C271919
    Temporarily install the rear support to rear shock absorber nut to the rear shock absorber assembly.


7. INSTALL REAR COIL SPRING

  1. C271924E01
    Install the rear coil spring.

    CAUTION:
    Do not use an impact wrench. It will damage the SST.

    NOTICE:
    1. Make sure that the end of the rear coil spring is positioned in the depression of the rear lower coil spring insulator.
    2. Ensure that the stud bolt is positioned 3.5° to the outside of the vehicle as shown in the illustration. The deviation should be within +-5°.


8. INSTALL REAR SHOCK ABSORBER WITH COIL SPRING (for 2WD)

  1. C166012
    Install the rear shock absorber with coil spring with the 3 nuts.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }

  1. C132464
    Install the rear shock absorber with coil spring with the 2 bolts and 2 nuts.

    Torque:
    290 N*m{ 2956 kgf*cm , 213 ft.*lbf }

    NOTICE:
    When installing the nuts, keep the bolts from rotating.

  1. C166011
    Fully tighten the rear support to rear shock absorber nut.

    Torque:
    55 N*m{ 561 kgf*cm , 40 ft.*lbf }


9. INSTALL REAR SHOCK ABSORBER WITH COIL SPRING (for 4WD)

  1. C166012
    Install the rear shock absorber with coil spring with the 3 nuts.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }

  1. C166010
    Install the rear shock absorber with coil spring with the 2 bolts and 2 nuts.

    Torque:
    290 N*m{ 2956 kgf*cm , 213 ft.*lbf }

    NOTICE:
    When installing the nuts, keep the bolts from rotating.

  1. C166011
    Fully tighten the rear support to rear shock absorber nut.

    Torque:
    55 N*m{ 561 kgf*cm , 40 ft.*lbf }


10. INSTALL REAR NO. 1 SUSPENSION SUPPORT COVER

  1. C166225
    Install the rear No. 1 suspension support cover.


11. INSTALL REAR STABILIZER LINK ASSEMBLY (for 2WD)

  1. C167798E02
    Install the rear stabilizer link assembly to the rear shock absorber with coil spring with the nut.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.


12. INSTALL REAR STABILIZER LINK ASSEMBLY (for 4WD)

  1. C166214E02
    Install the rear stabilizer link assembly to the rear shock absorber with coil spring with the nut.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.


13. INSTALL REAR SPEED SENSOR WIRE (for 2WD)

  1. C167793
    Install the rear speed sensor wire to the rear shock absorber with coil spring with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    Do not twist the rear speed sensor wire when installing it.


14. INSTALL REAR SPEED SENSOR (for 4WD)

  1. C166254
    Install the rear speed sensor to the rear shock absorber with coil spring with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    Do not twist the rear speed sensor wire when installing it.


15. INSTALL REAR FLEXIBLE HOSE (for 2WD)

  1. C167792
    Install the rear flexible hose to the rear shock absorber with coil spring with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not twist the rear flexible hose when installing it.


16. INSTALL REAR FLEXIBLE HOSE (for 4WD)

  1. C166009
    Install the rear flexible hose to the rear shock absorber with coil spring with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not twist the rear flexible hose when installing it.


17. INSTALL DECK SIDE TRIM

  1. B173624
    Engage the 3 guides and 4 claws as shown in the illustration.

  1. B173596
    Install the deck side trim LH with the bolt.


18. INSTALL DECK SIDE TRIM COVER

  1. B175144
    Engage the 2 claws and install the deck side trim cover LH.


19. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


20. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

HINT:
Click here

← INSTALLATION (Aug 2008 – Jun 2010)DISPOSAL (from May 2007) →