2007-2013 Highlander Kluger · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

C167805E01
  1. Temporarily install the rear No. 1 suspension arm assembly to the rear suspension member with the bolt.

    NOTICE:
    Ensure that the identification mark faces the rear side of the vehicle.

  1. Temporarily install the rear No. 1 suspension arm assembly to the rear axle carrier sub-assembly with the bolt and the nut.

    NOTICE:
    Since a stopper nut is used, temporarily tighten the bolt.


2. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY

C170680E01
  1. Temporarily install the rear No. 2 suspension arm assembly to the rear suspension member with the bolt.

    NOTICE:
    Ensure that the identification mark faces the rear side of the vehicle.

  1. Temporarily install the rear No. 2 suspension arm assembly to the rear axle carrier sub-assembly with the bolt and the nut.

    NOTICE:
    Since a stopper nut is used, temporarily tighten the bolt.


3. STABILIZE SUSPENSION

  1. C167817E01
    Jack up the rear axle carrier, placing a wooden block underneath to avoid damage. Apply load to the suspension so that the installed bolt of the rear No. 1 suspension arm (inner side) is horizontally aligned with the center of the rear axle hub.

    CAUTION:
    Do not jack up the rear axle carrier subassembly too high as the vehicle may fall.

    NOTICE:
    Do not bend the brake dust cover.

    HINT:
    1. If the rear drive shaft assembly cannot be positioned horizontally as shown in the illustration even when the rear axle carrier subassembly is jacked up, apply additional load to the vehicle such as by having a person sit in the rear seat.
    2. Use the same procedures for the RH side and LH side.


4. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

  1. C167806E01
    Using SST and a socket wrench (19 mm), fully tighten the bolt.

    Torque:
    without SST:
    120 N*m{ 1223 kgf*cm , 88 ft.*lbf }
    with SST:
    89 N*m{ 904 kgf*cm , 65 ft.*lbf }

    SST
    09961-00950  

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 425 mm (16.73 in.).
    2. This torque value is effective when SST is parallel to the torque wrench.
    3. The final torque must be applied under standard vehicle height conditions.

  1. C170679
    Fully tighten the bolt

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


5. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

C167804E02
  1. Fully tighten the bolts.

    Torque:
    Bolt (A):
    120 N*m{ 1223 kgf*cm , 88 ft.*lbf }
    Bolt (B):
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


6. INSTALL REAR STABILIZER BAR

  1. C170677E01
    Install the rear stabilizer bar with the 4 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


7. INSTALL REAR STABILIZER LINK ASSEMBLY LH

  1. C167797E02
    Install the rear stabilizer link assembly LH to the rear stabilizer bar with the nut.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.


8. INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.


9. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


10. INSTALL SPARE WHEEL CARRIER LOCK COVER

11. INSTALL SPARE TIRE

12. INSTALL LOWER SPARE WHEEL CARRIER HINGE COVER

13. INSTALL DECK TRIM SERVICE HOLE COVER

14. INSTALL REAR MAT

  1. B173249
    Install the rear mat.


15. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.


16. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Tonneau Cover)

  1. B173244
    Engage the 2 guides and install the No. 2 deck board sub-assembly.


17. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY (w/ Tonneau Cover)

  1. B173242
    Engage the 2 guides and install the No. 3 deck board sub-assembly.


18. INSTALL DECK BOARD ASSEMBLY

  1. B173240
    Install the deck board sub-assembly.


19. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

HINT:
Click here

← REMOVAL (from Jul 2010)INSTALLATION (Aug 2008 – Jun 2010) →