2007-2013 Highlander Kluger · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. TEMPORARILY INSTALL REAR STABILIZER BAR

  1. C166252E01
    Temporarily install the rear stabilizer bar with the identification mark positioned on the left side of the vehicle.


2. TEMPORARILY INSTALL REAR STABILIZER BAR BRACKET LH (for Front Side)

  1. C166251
    Temporarily install the rear stabilizer bar bracket LH (front side) with the bolt.

    HINT:
    Loosely tighten the bolt so that the bracket can be moved by hand.


3. TEMPORARILY INSTALL REAR STABILIZER BAR BRACKET RH (for Front Side)

  1. C166250
    Temporarily install the rear stabilizer bar bracket RH (front side) with the 2 bolts.

    HINT:
    Loosely tighten the bolts so that the bracket can be moved by hand.


4. INSTALL REAR STABILIZER BUSHING (for LH Side)

  1. C166249E01
    Install the rear stabilizer bushing (LH side) to the rear stabilizer bar.

    NOTICE:
    Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown in the illustration.


5. INSTALL REAR STABILIZER BUSHING (for RH Side)

  1. C166247E01
    Install the rear stabilizer bushing (RH side) to the rear stabilizer bar.

    NOTICE:
    Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown in the illustration.


6. INSTALL REAR STABILIZER BAR BRACKET LH (for Rear Side)

  1. C166245
    Install the rear stabilizer bar bracket LH (rear side) with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


7. INSTALL REAR STABILIZER BAR BRACKET RH (for Rear Side)

  1. C166244
    Install the rear stabilizer bar bracket RH (rear side) with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


8. FULLY TIGHTEN REAR STABILIZER BAR BRACKET LH (for Front Side)

  1. C166234
    Fully tighten the bolt.

    Torque:
    54 N*m{ 550 kgf*cm , 40 ft.*lbf }


9. FULLY TIGHTEN REAR STABILIZER BAR BRACKET RH (for Front Side)

  1. C167782
    Fully tighten the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }


10. INSTALL REAR STABILIZER LINK ASSEMBLY LH

  1. C166214E02
    Install the rear stabilizer link assembly LH to the rear shock absorber with coil spring LH with the nut.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.

  1. C166215E02
    Install the rear stabilizer link assembly LH to the rear stabilizer bar with the nut.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.


11. INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.


12. INSTALL TAIL EXHAUST PIPE ASSEMBLY

  1. A160224
    Using vernier calipers, measure the free length of the compression spring.
    Minimum
    40.5 mm (1.59 in.)

    HINT:
    If the length is less than the minimum, replace the compression spring.

  1. A138040E01
    Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the center exhaust pipe assembly.

    NOTICE:
    1. Tap in the gasket in the correct direction.
    2. Do not reuse the removed gasket.
    3. Do not push in the gasket while installing the tail exhaust pipe assembly.

  1. Connect the exhaust pipe support, and install the tail exhaust pipe assembly.

  1. A170139
    Install the 2 compression springs and 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


13. INSPECT FOR EXHAUST GAS LEAK
If exhaust gas is leaking, repair the leak. Replace damaged or worn parts as necessary.

14. INSTALL REAR WHEELS

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


15. INSTALL SPARE WHEEL CARRIER LOCK COVER

16. INSTALL SPARE TIRE

17. INSTALL LOWER SPARE WHEEL CARRIER HINGE COVER

18. INSTALL DECK TRIM SERVICE HOLE COVER

19. INSTALL REAR MAT

  1. B173249
    Install the rear mat.


20. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.


21. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Tonneau Cover)

  1. B173244
    Engage the 2 guides and install the No. 2 deck board sub-assembly.


22. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY (w/ Tonneau Cover)

  1. B173242
    Engage the 2 guides and install the No. 3 deck board sub-assembly.


23. INSTALL DECK BOARD ASSEMBLY

  1. B173240
    Install the deck board sub-assembly.

← INSPECTION (from May 2007)INSTALLATION (Aug 2008 – Jun 2010) →