2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Steering Pad Switch Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the navigation receiver assembly.
If there is an open in the circuit, the navigation system cannot be operated using the steering pad switch assembly.
If there is a short in the circuit, the resulting condition is the same condition as when a switch is continuously pressed. Therefore, the navigation receiver assembly cannot be operated using the steering pad switch assembly, and the navigation receiver assembly itself cannot function.

WIRING DIAGRAM

E176601E42

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System). Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).


1. INSPECT NAVIGATION RECEIVER ASSEMBLY

  1. E168561E78
    Disconnect the E2 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E2-7 (SW1) - E2-6 (SWG)
    No switch pushed
    95 to 105 kΩ
    E2-7 (SW1) - E2-6 (SWG)
    Seek+ switch pushed
    Below 2.5 Ω
    E2-7 (SW1) - E2-6 (SWG)
    Seek- switch pushed
    312.5 to 345.4 Ω
    E2-7 (SW1) - E2-6 (SWG)
    Volume+ switch pushed
    950 to 1050 Ω
    E2-7 (SW1) - E2-6 (SWG)
    Volume- switch pushed
    2954.5 to 3265.5 Ω
    E2-8 (SW2) - E2-6 (SWG)
    No switch pushed
    95 to 105 kΩ
    E2-8 (SW2) - E2-6 (SWG)
    MODE switch pushed
    Below 2.5 Ω
    E2-8 (SW2) - E2-6 (SWG)
    Voice switch pushed
    2954.5 to 3265.5 Ω
    E2-8 (SW2) - E2-6 (SWG)
    On Hook switch pushed
    312.5 to 345.4 Ω
    E2-8 (SW2) - E2-6 (SWG)
    Off Hook switch pushed
    950 to 1050 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT SPIRAL CABLE SUB-ASSEMBLY

  1. E168547E91
    Disconnect the z2 steering pad switch assembly and D53 spiral cable sub-assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-8 (EAU) - D53-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-10 (AU1) - D53-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-9 (AU2) - D53-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Refer to the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *a
    Component without harness connected
    (Spiral Cable Sub-assembly)
    *b
    Steering Pad Switch Side
    *c
    Vehicle Side



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


3. INSPECT STEERING PAD SWITCH ASSEMBLY

  1. Disconnect the z2 steering pad switch assembly connector.E136177E21

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    z2-10 (AU1) - z2-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    z2-10 (AU1) - z2-8 (EAU)
    Seek+ switch pushed
    Below 2.5 Ω
    z2-10 (AU1) - z2-8 (EAU)
    Seek- switch pushed
    312.5 to 345.4 Ω
    z2-10 (AU1) - z2-8 (EAU)
    Volume+ switch pushed
    950 to 1050 Ω
    z2-10 (AU1) - z2-8 (EAU)
    Volume- switch pushed
    2954.5 to 3265.5 Ω
    z2-9 (AU2) - z2-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    z2-9 (AU2) - z2-8 (EAU)
    MODE switch pushed
    Below 2.5 Ω
    z2-9 (AU2) - z2-8 (EAU)
    Voice switch pushed
    2954.5 to 3265.5 Ω
    z2-9 (AU2) - z2-8 (EAU)
    On Hook switch pushed
    312.5 to 345.4 Ω
    z2-9 (AU2) - z2-8 (EAU)
    Off Hook switch pushed
    950 to 1050 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch Assembly)
    *b
    Volume-
    *c
    Volume+
    *d
    Seek-
    *e
    Seek+
    *f
    MODE
    *g
    On Hook
    *h
    Off Hook
    *i
    Voice
    -
    -



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)


← Steering Pad Switch Circuit (Aug 2008 – Jun 2010)Illumination Circuit (May 2007 – Jul 2008) →