2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Radio Broadcast cannot be Received or Poor Reception

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

INSPECTION PROCEDURE


1. CHECK RADIO RECEIVER
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.

      Result:
      Result
      Proceed to
      Automatic station search function does not stop
      A
      Automatic station search function stops on a station
      B



B
REPLACE RADIO RECEIVER (Click here)
A


2. CHECK OPTIONAL COMPONENTS
  1. Check optional components (sunshade film, telephone antenna, etc.).

    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      Result:
      Result
      Proceed to
      Optional components are installed
      A
      Optional components are not installed
      B

      NOTICE:
      Do not remove any optional components installed by the customer without his or her consent.



B
Go to step 3
A

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3. CHECK RADIO RECEIVER

  1. E187251
    Preparation for check
    1. Remove the antenna connector from the radio receiver.

  1. Check for noise

    1. Turn the ignition switch to ACC with the radio receiver connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire or other metal object on the radio receiver antenna jack and check that noise can be heard from the speakers.

      OK:
      Noise can be heard from the speakers.



NG
REPLACE RADIO RECEIVER (Click here)
OK


4. INSPECT RADIO RECEIVER

  1. E188455E17
    Disconnect the radio receiver connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    RA1-5 (ANT+) - Body ground
    Ignition switch ACC
    Radio switch on and AM or FM selected
    11 to 14 V

    Text in Illustration 
    *a
    Component without harness connected
    (Radio Receiver)



NG
REPLACE RADIO RECEIVER (Click here)
OK


5. CHECK ANTENNA CORD
  1. Remove the antenna connector of the radio receiver and antenna.

  1. Measure the resistance between the antenna cord and radio receiver to check for an open circuit in the antenna cord.

    Standard Resistance:
    Below 1 Ω

  1. Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.

    Standard Resistance:
    10 kΩ or higher



NG
REPLACE ANTENNA CORD (Click here)
OK


6. CHECK WINDOW GLASS ANTENNA WIRE

  1. E111994E01
    Check for continuity of the antenna.

    HINT:
    Check for continuity at the center of each antenna wire as shown in the illustration.

    NOTICE:
    When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of the negative probe and press the foil against the wire with your finger as shown in the illustration.

    OK:
    There is continuity in the antenna.



NG
REPAIR WINDOW GLASS ANTENNA WIRE
OK


7. REPLACE AMPLIFIER ANTENNA ASSEMBLY
  1. Replace the amplifier antenna assembly and check if radio broadcasts can be received normally.

    OK:
    Radio broadcasts can be received.



NG
REPLACE RADIO RECEIVER (Click here)
OK

NORMAL OPERATION


← Radio Broadcast cannot be Received or Poor Reception (Aug 2008 – Jun 2010)Poor Sound Quality in All Modes (Low Volume) (May 2007 – Jul 2008) →