2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Radio Broadcast cannot be Received or Poor Reception

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

INSPECTION PROCEDURE


1. CHECK RADIO RECEIVER
  1. Check the radio's automatic station search function.

    1. Check the radio's automatic station search function by activating it.

      OK:
      The radio's automatic station search function works properly.



NG
Go to step 2
OK

REPLACE RADIO RECEIVER (Click here)

2. CHECK OPTIONAL COMPONENTS
  1. Check optional components (sun-shade film, telephone antenna, etc.).

    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      OK:
      Optional components are installed.

      NOTICE:
      Do not remove any optional components installed by the customer without his or her consent.



NG
Go to step 3
OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3. CHECK RADIO RECEIVER

  1. E050367
    Preparation for check
    1. Remove the antenna plug from the radio receiver.

  1. Check for noise

    1. Turn the ignition switch on (ACC) with the radio receiver connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire, or other metal object on the radio receiver's antenna jack and check that noise can be heard from the speaker.

      OK:
      Noise occurs.



NG
REPLACE RADIO RECEIVER (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - ANTENNA AMPLIFIER)

  1. E155443E01
    Disconnect the radio receiver connector and the antenna amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-8 (ANT) - E5-1 (B)
    Always
    Below 1 Ω
    E6-8 (ANT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT RADIO RECEIVER

  1. E150785E05
    Reconnect the radio receiver connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E5-1 (B) - Body ground
    Ignition switch on (IG)
    Radio switch ON
    11 to 14 V



NG
REPLACE RADIO RECEIVER (Click here)
OK


6. CHECK ANTENNA CORD
  1. Remove the antenna plug of the radio receiver and antenna.

  1. Measure the resistance between the antenna and radio receiver to check for an open circuit in the antenna cord.

    Standard resistance:
    Below 1 Ω

  1. Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.

    Standard resistance:
    10 kΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG
    (for Glass Antenna Type)
    B
    NG
    (for Pole Antenna Type)
    C



B
REPLACE ANTENNA CORD (for Glass Antenna Type) (Click here)

C
REPLACE ANTENNA CORD (for Pole Antenna Type) (Click here)
A


7. CONFIRM MODEL

Result:
Result
Proceed to
Glass Antenna Type
A
Pole Antenna Type
B



B
Go to step 10
A


8. CHECK GLASS ANTENNA

  1. E111994E01
    Check for continuity of the antenna.

    HINT:
    Check for continuity at the center of each antenna wire as shown in the illustration.

    NOTICE:
    When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of the negative probe and press the foil against the wire with your finger, as shown in the illustration.

    OK:
    There is continuity in the antenna.



NG
REPAIR GLASS ANTENNA (Click here)
OK


9. REPLACE AMPLIFIER ANTENNA
  1. Replace the amplifier antenna and check if radio broadcasts can be received normally.

    OK:
    Radio broadcasts can be received.



NG
REPLACE RADIO RECEIVER (Click here)
OK

NORMAL OPERATION

10. CHECK PULL TOP ANTENNA POLE SUB-ASSEMBLY
  1. Check that the pull top antenna pole sub-assembly is securely installed.

    OK:
    The pull top antenna pole sub-assembly is installed properly.



NG
CHECK AND REPLACE PULL TOP ANTENNA POLE SUB-ASSEMBLY (Click here)
OK


11. REPLACE FENDER ANTENNA ASSEMBLY
  1. Replace the fender antenna assembly and check if radio broadcasts can be received normally.

    OK:
    Radio broadcasts can be received.



NG
REPLACE RADIO RECEIVER (Click here)
OK

NORMAL OPERATION


← Radio Broadcast cannot be Received or Poor Reception (May 2007 – Jul 2008)Radio Broadcast cannot be Received or Poor Reception (from Jul 2010) →