2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Speedometer Malfunction

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

The meter CPU receives vehicle speed signals from the skid control ECU via the CAN communication lines (CAN No. 1 Bus). The vehicle speed sensor detects the voltage that varies according to the vehicle speed. The skid control ECU supplies power to the vehicle speed sensor. The skid control ECU detects vehicle speed signals based on the pulses of the voltage.

HINT:
If the vehicle speed sensor circuit has a malfunction, the skid control ECU stores DTCs. Perform troubleshooting with the "Brake Control System" (Click here).


WIRING DIAGRAM

E143765E07

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).

    Result:
    Result
    Proceed to
    CAN communication DTC is not output.
    A
    CAN communication DTC is output.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Check the operation by referring to the table below.

    Combination Meter: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    0, 40, 80, 120, 160, 200, 240 km/h
    -

    OK:
    Needle indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost same as actual speed (When driving)
    -

    OK:
    Vehicle speed displayed on the tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 4
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

4. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. Check the values by referring to the table below.

    ABS/VSC/TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR/FL/RR/RL Wheel Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Almost same as actual speed (When driving)
    -

    OK:
    Vehicle speed displayed on the tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
GO TO BRAKE CONTROL SYSTEM (Click here)
OK


5. REPLACE SKID CONTROL ECU
  1. Replace the skid control ECU with a new or a normal one (Click here).

    OK:
    The operation of the speedometer returns to normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

END


← Entire Combination Meter does not Operate (from Jul 2010)Speedometer Malfunction (Aug 2008 – Jun 2010) →