Operating Light Control Rheostat does not Change Light Brightness
Circuit diagnosis · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
In this circuit the meter CPU receives signals for adjusting illumination on the meter. The meter CPU detects the illumination level selected by the user according to the position of the rheostat knob.- HINT:
- This model is equipped with an optitron meter, therefore the meter illuminates even in the daytime.
- The meter illumination level can be adjusted by turning the rheostat.
- The meter illumination dims when the light control switch is turned to the TAIL or HEAD position at night.
- Turning the rheostat knob fully upwards cancels the above dimmer control.
- This model is equipped with an optitron meter, therefore the meter illuminates even in the daytime.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. SYSTEM CHECK |
Ignition switch on (IG).
Turn the light control rheostat knob fully upwards.
Turn the light control rheostat knob fully downwards.
Turn the light control rheostat knob fully upwards and turn the light control switch to the TAIL or HEAD position.
Check the meter illumination.
- Result:
Result
Proceed to
Meter illumination does not change when operating the light control rheostat knob.
A
Dimmer cancel does not operate (Meter illumination does not dim).
B
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (RHEOSTAT) |
Connect the intelligent tester to the DLC3.
Ignition switch on (IG).
Turn the tester on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Check the values by referring to the table below.
Combination Meter: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Rheostat value
Light control rheostat/Min.: 0%, Max.: 100%
Light control rheostat switch is Dark (0%) → Bright (100%)
-
- OK:
- The value displayed on the tester gradually changes with the actual rheostat operation.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (TAIL CANCEL SW) |
Connect the intelligent tester to the DLC3.
Ignition switch on (IG).
Turn the tester on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Check the values by referring to the table below.
Combination Meter: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Tail Cancel SW
Tail cancel switch is/ OFF or ON
OFF: The light control rheostat knob is not turned fully downwards
-
ON: The light control rheostat knob is turned fully upwards
-
- OK:
- Condition displayed on the tester is the same as the actual rheostat position.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - LIGHT CONTROL RHEOSTAT) |
Disconnect the E1 and D3 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
E1-4 (SW1) - D3-7 (T)
Always
Below 1 Ω
E1-24 (SW2) - D3-3 (RV)
Always
Below 1 Ω
E1-39 (SW3) - D3-1 (E)
Always
Below 1 Ω
D3-1 (E) - Body ground
Always
10 kΩ or higher
D3-3 (RV) - Body ground
Always
10 kΩ or higher
D3-7 (T) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. INSPECT LIGHT CONTROL RHEOSTAT |
Remove the light control rheostat with the connector still connected.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D3-1 (E) - D3-3 (RV)
Turn the light control rheostat knob fully upwards
8 kΩ or higher
D3-1 (E) - D3-3 (RV)
Rheostat knob position is between MIN. and MAX.
The value changes gradually
(Between 1 Ω and 8 kΩ)
D3-1 (E) - D3-3 (RV)
Turn the light control rheostat knob fully downwards
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (COMBINATION METER - LIGHT CONTROL RHEOSTAT) |
Disconnect the E1 and D3 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D3-5 (TC) - E1-23 (TC)
Always
Below 1 Ω
D3-7 (T) - E1-4 (SW1)
Always
Below 1 Ω
D3-5 (TC) - Body ground
Always
10 kΩ or higher
D3-7 (T) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. INSPECT LIGHT CONTROL RHEOSTAT |
Remove the light control rheostat with the connector still connected.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D3-5 (TC) - D3-7 (T)
Turn the light control rheostat knob fully downwards
Below 1 Ω
D3-5 (TC) - D3-7 (T)
Turn the light control rheostat knob fully upwards (Tail cancel ON)
8 kΩ or higher
|
|
||||
| OK | ||
| ||
