P0793 Intermediate Shaft Speed Sensor "A"
Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
This sensor detects the rotation speed of the counter gear. By comparing the counter gear speed signal (NC) with the direct clutch speed sensor signal (NT), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. Thus smooth gear shifting is performed.| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0793 |
ECM detects conditions (a), (b) and (c) continuously for 5 sec. or more: (1-trip detection logic)
|
|
Check the waveform between terminals NC+ and NC- of the ECM connector.


| Terminal |
NC+ - NC- |
| Tool setting |
1 V/DIV, 1ms/DIV |
| Vehicle condition |
Vehicle speed 30 km/h (19 mph): (3rd gear) Engine speed 1400 rpm |
MONITOR DESCRIPTION
The NC terminal of the ECM detects a revolution signal from the speed sensor (NC) (counter gear rpm). The ECM calculates a gearshift comparing the speed sensor (NT) with the speed sensor (NC).While the vehicle is operating in 2nd, 3rd, 4th or 5th gear in the shift position of D, if the counter gear revolution is less than 300 rpm *1although the output shaft revolution is more than 1,000 rpm *2, the ECM detects the trouble, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is 50 km/h (31 mph) or more.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Using Intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect Intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Select the item "Powertrain / Engine and ECT / Data List".
According to the display on the tester, read the "Data List".
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
SPD (NC)
Counter Gear Speed/
display: 50 r/min
- HINT:
- 3rd when shift lever position is D position (After warming up the engine):
- Intermediate shaft speed (NC) becomes close to the engine speed.
- Intermediate shaft speed (NC) becomes close to the engine speed.
-
- HINT:
- SPD (NC) is always 0 while driving:
Open or short in the sensor or circuit.
- SPD (NC) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
Sensor trouble, improper installation, or intermittent connection trouble of the circuit.
- SPD (NC) is always 0 while driving:
| 1. INSPECT SPEED SENSOR INSTALLATION |
Check the speed sensor installation.

- OK:
- The installation bolt is tightened properly and there is no clearance between the sensor and transaxle case.
|
|
||||
| OK | |
| 2. INSPECT SPEED SENSOR (NC) |
Disconnect the speed sensor connector from the transaxle.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
560 to 680 Ω
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (SPEED SENSOR - ECM) |
Connect the speed sensor connector.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
B2-34 (NC+) - B2-26 (NC-)
20°C (68°F)
560 to 680 Ω
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for short):
Tester Connection
Condition
Specified Condition
B2-34 (NC+) - Body ground
Always
10 kΩ or higher
B2-26 (NC-) - Body ground
|
|
||||
| OK | ||
| ||
