2007-2013 Highlander Kluger · Service Manual TRANSMISSION

P0982 Shift Solenoid "D" Control Circuit Low (Shift Solenoid Valve S4)

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

Shifting from 1st to 5th is performed in combination with "ON" and "OFF" operation of the shift solenoid valves SL1, SL2, SL3, S4 and SR which are controlled by the ECM. If an open or short circuit occurs in either of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (Fail safe function).
DTC No.
DTC Detection Condition
Trouble Area
P0982
ECM detects short in solenoid valve S4 circuit 2 times when solenoid valve S4 is operated (1-trip detection logic)
  1. Short in shift solenoid valve S4 circuit
  2. Shift solenoid valve S4
  3. ECM
P0983
ECM detects open in solenoid valve S4 circuit 2 times when solenoid valve S4 is not operated (1-trip detection logic)
  1. Open in shift solenoid valve S4 circuit
  2. Shift solenoid valve S4
  3. ECM

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF". When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL, and stores the DTC. And the ECM performs the fail-safe function and turns the other normal shift solenoid valves "ON/OFF" (In case of an open or short circuit, the ECM stops sending current to the circuit.) (Click here).

WIRING DIAGRAM

G031165E93

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (S4)

  1. C113969E54
    Disconnect the transmission wire connector from the transaxle.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (S4) - Body ground
    20°C (68°F)
    11 to 15 Ω



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C168530E17
    Connect the transmission wire connector to the transaxle.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B2-10 (S4) - Body ground
    20°C (68°F)
    11 to 15 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (for 2GR-FE) (Click here)

3. INSPECT SHIFT SOLENOID VALVE (S4)

  1. C113971E08
    Remove the shift solenoid valve S4.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Solenoid Connector (S4) - Solenoid Body (S4)
    20°C (68°F)
    11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE (S4) (Click here)
OK

REPAIR OR REPLACE TRANSMISSION WIRE (Click here)


← P0798 Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3) (from Jul 2010)P0982 Shift Solenoid "D" Control Circuit Low (Shift Solenoid Valve S4) (+ P0983) (Aug 2008 – Jun 2010) →