01-D6 No Master
Diagnostic trouble codes · Vehicles built from Jul 2010
Also covers:
- 01-D7 Connection Check Error
DESCRIPTION
| DTC No. |
DTC Detection Condition |
Trouble Area |
| 01-D6*1 |
Either condition is met:
|
|
| 01-D7*2 |
Either condition is met:
|
- HINT:
- *1: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
- *2: When 210 seconds have elapsed after disconnecting the power supply connector of the master component with the ignition switch ON or ACC, this DTC is stored.
- *1: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
- NOTICE:
- Before starting troubleshooting, be sure to clear the DTCs stored due to the reasons described in the Hint above. Then, check for DTCs and troubleshoot according to the output DTCs.
- The radio receiver is the master unit.
- Be sure to clear and recheck for DTCs after the inspection is completed to confirm that no DTCs are output.
- Before starting troubleshooting, be sure to clear the DTCs stored due to the reasons described in the Hint above. Then, check for DTCs and troubleshoot according to the output DTCs.
INSPECTION PROCEDURE
- NOTICE:
- Be sure to read Description before performing the following procedure.
| 1. CHECK RADIO RECEIVER POWER SOURCE CIRCUIT |
- HINT:
- Refer to Radio Receiver Power Source Circuit (Click here).
- If the power source circuit is operating normally, proceed to the next step.
| NEXT | |
| 2. IDENTIFY COMPONENT WHICH HAS STORED THIS CODE |
Enter diagnostic mode.


Press preset switch "2" to change the mode to "Detailed Information Mode".
Identify the component which has stored this code.
Component Table Component
Physical Address
Multi-media interface ECU
388
- HINT:
- The physical address "P440" shown in the above example indicates the stereo component amplifier.
- For details of the DTC display, refer to DTC Check/Clear (Click here).
- The physical address "P440" shown in the above example indicates the stereo component amplifier.
| NEXT | |
| 3. CHECK POWER SOURCE CIRCUIT OF COMPONENT WHICH HAS STORED THIS CODE |
Inspect the power source circuit of the component which has stored this code.If the power source circuit is operating normally, proceed to the next step.
Component Table Component
Proceed to
Multi-media interface ECU
Multi-media interface ECU power source circuit (Click here)
| NEXT | |
| 4. INSPECT RADIO RECEIVER |
Disconnect the radio receiver connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E24-9 (TXM+) - E24-10 (TXM-)
Always
60 to 80 Ω
Text in Illustration *a
Component without harness connected
(Radio Receiver)
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMPONENT WHICH HAS STORED THIS CODE) |
- HINT:
- For details of the connectors, refer to Terminals of ECU (Click here).
Referring to the following AVC-LAN wiring diagram, check the AVC-LAN circuit between the radio receiver and component which has stored this code.
Disconnect all connectors between the radio receiver and component which has stored this code.
Check for an open or short in the AVC-LAN circuit between the radio receiver and component which has stored this code.
- OK:
- There is no open or short circuit.


|
|
||||
| OK | |
| 6. REPLACE COMPONENT WHICH HAS STORED THIS CODE |
Replace the component which has stored this code with a known good one.
| NEXT | |
| 7. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 8. RECHECK FOR DTC |
Recheck for DTCs and check if the same DTC is output again.
- OK:
- No DTCs are output.
|
|
||||
| OK | ||
| ||
