B2312 Driver Side Door Master Switch Malfunction
Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The portion of the power window control system that is located in the driver door consists of a power window master switch, regulator, and a motor with an integrated ECU. The driver door power window regulator motor is controlled by the ECU when the power window master switch is operated (models with jam protection).When the ECU determines that the power window master switch is stuck, DTC B2312 is set.
- NOTICE:
- The power window control system uses a serial communication protocol (LIN) to communicate with the main body ECU. Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B2312 |
The power window regulator master switch is stuck |
|
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK DTC OUTPUT |
Turn the ignition switch off.
Wait for at least 10 seconds, and then turn the ignition switch on (IG).
Check whether the DTC output recurs.
- Result:
Result
Proceed to
B2312
A
No output
B
|
|
||||
| A | |
| 2. INSPECT POWER WINDOW MASTER SWITCH |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
8 (U) - 1 (E) - 4 (A)
Auto UP
Below 1 Ω
8 (U) - 1 (E)
Manual UP
Below 1 Ω
5 (D) - 1 (E)
Manual DOWN
Below 1 Ω
4 (A) - 5 (D) - 1 (E)
Auto DOWN
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
1 (U) - 9 (E) - 4 (A)
Auto UP
Below 1 Ω
1 (U) - 9 (E)
Manual UP
Below 1 Ω
5 (D) - 9 (E)
Manual DOWN
Below 1 Ω
4 (A) - 5 (D) - 9 (E)
Auto DOWN
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - WINDOW REGULATOR MOTOR) |
for LHD:
Disconnect the M1 and H1 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
M1-8 (U) - H1-10 (UP1)
Always
Below 1 Ω
M1-3 (LED) - H1-5 (LED)
Always
Below 1 Ω
M1-4 (A) - H1-4 (AUTO)
Always
Below 1 Ω
M1-5 (D) - H1-7 (DWN1)
Always
Below 1 Ω
M1-8 (U) - Body ground
Always
10 kΩ or higher
M1-3 (LED) - Body ground
Always
10 kΩ or higher
M1-4 (A) - Body ground
Always
10 kΩ or higher
M1-5 (D) - Body ground
Always
10 kΩ or higher
for RHD:
Disconnect the L1 and G10 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
L1-1 (U) - G10-10 (UP1)
Always
Below 1 Ω
L1-3 (LED) - G10-5 (LED)
Always
Below 1 Ω
L1-4 (A) - G10-4 (AUTO)
Always
Below 1 Ω
L1-5 (D) - G10-7 (DWN1)
Always
Below 1 Ω
L1-1 (U) - Body ground
Always
10 kΩ or higher
L1-3 (LED) - Body ground
Always
10 kΩ or higher
L1-4 (A) - Body ground
Always
10 kΩ or higher
L1-5 (D) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
