2007-2013 Highlander Kluger · Service Manual BODY

B2312 Driver Side Door Master Switch Malfunction

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The portion of the power window control system that is located in the driver door consists of a power window master switch, regulator, and a motor with an integrated ECU. The driver door power window regulator motor is controlled by the ECU when the power window master switch is operated (models with jam protection).
When the ECU determines that the power window master switch is stuck, DTC B2312 is set.

NOTICE:
The power window control system uses a serial communication protocol (LIN) to communicate with the main body ECU. Inspect the communication function by following HOW TO PROCEED WITH TROUBLESHOOTING. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

DTC Code
DTC Detection Condition
Trouble Area
B2312
The power window regulator master switch is stuck
  1. Power window regulator motor (on driver side)
  2. Power window master switch
  3. Wire harness
  4. Power window master switch is held in the same position for more than 20 seconds

WIRING DIAGRAM

B175977E04
B175977E05

INSPECTION PROCEDURE


1. CHECK DTC OUTPUT
  1. Turn the ignition switch off.

  1. Wait for at least 10 seconds, and then turn the ignition switch on (IG).

  1. Check whether the DTC output recurs.

    Result:
    Result
    Proceed to
    B2312
    A
    No output
    B



B
END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)
A


2. INSPECT POWER WINDOW MASTER SWITCH

  1. B164359E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    8 (U) - 1 (E) - 4 (A)
    Auto UP
    Below 1 Ω
    8 (U) - 1 (E)
    Manual UP
    Below 1 Ω
    5 (D) - 1 (E)
    Manual DOWN
    Below 1 Ω
    4 (A) - 5 (D) - 1 (E)
    Auto DOWN
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    1 (U) - 9 (E) - 4 (A)
    Auto UP
    Below 1 Ω
    1 (U) - 9 (E)
    Manual UP
    Below 1 Ω
    5 (D) - 9 (E)
    Manual DOWN
    Below 1 Ω
    4 (A) - 5 (D) - 9 (E)
    Auto DOWN
    Below 1 Ω



NG
REPLACE POWER WINDOW MASTER SWITCH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - WINDOW REGULATOR MOTOR)

  1. for LHD:

    1. B175976E09
      Disconnect the M1 and H1 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M1-8 (U) - H1-10 (UP1)
      Always
      Below 1 Ω
      M1-3 (LED) - H1-5 (LED)
      Always
      Below 1 Ω
      M1-4 (A) - H1-4 (AUTO)
      Always
      Below 1 Ω
      M1-5 (D) - H1-7 (DWN1)
      Always
      Below 1 Ω
      M1-8 (U) - Body ground
      Always
      10 kΩ or higher
      M1-3 (LED) - Body ground
      Always
      10 kΩ or higher
      M1-4 (A) - Body ground
      Always
      10 kΩ or higher
      M1-5 (D) - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. B175976E10
      Disconnect the L1 and G10 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      L1-1 (U) - G10-10 (UP1)
      Always
      Below 1 Ω
      L1-3 (LED) - G10-5 (LED)
      Always
      Below 1 Ω
      L1-4 (A) - G10-4 (AUTO)
      Always
      Below 1 Ω
      L1-5 (D) - G10-7 (DWN1)
      Always
      Below 1 Ω
      L1-1 (U) - Body ground
      Always
      10 kΩ or higher
      L1-3 (LED) - Body ground
      Always
      10 kΩ or higher
      L1-4 (A) - Body ground
      Always
      10 kΩ or higher
      L1-5 (D) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side) (Click here)


← B2312 Driver Side Door Master Switch Malfunction (Aug 2008 – Jun 2010)B2313 Glass Position Initialization Incomplete (May 2007 – Jul 2008) →