2007-2013 Highlander Kluger · Service Manual BODY

Glass Hatch Opener System does not Operate

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The glass hatch opener system enables the back door glass to be opened when the glass hatch opener switch is pressed.

WIRING DIAGRAM

B172592E02

INSPECTION PROCEDURE


1. SYSTEM CHECK
  1. Confirm that the vehicle is equipped with the smart entry and start system.

    Result:
    Result
    Proceed to
    w/ Smart Entry and Start System
    A
    w/o Smart Entry and Start System
    B



B
Go to step 3
A


2. CHECK SMART ENTRY AND START SYSTEM
  1. When the back door entry lock switch is operated, check that the back door lock.

    OK:
    Back door entry lock function operates normally.



NG
GO TO SMART ENTRY AND START SYSTEM (Click here)
OK


3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select the item below in the ACTIVE TEST and then check that the relay operates.

    Main Body (Main Body ECU): 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Glass Hatch Open
    Operate Glass Hatch
    ON or OFF
    -

    OK:
    Glass hatch operates.



NG
Go to step 6
OK


4. READ VALUE USING INTELLIGENT TESTER (GLASS HATCH COURTESY SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select the items below in the DATA LIST, and read the displays on the intelligent tester.

    Main Body (Main Body ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Glass Hatch Courtesy Switch
    Glass hatch courtesy switch signal / ON or OFF
    ON: Glass hatch is open
    OFF: Glass hatch is closed
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 6
OK


5. READ VALUE USING INTELLIGENT TESTER (GLASS HATCH OPENER SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select the items below in the DATA LIST, and read the displays on the intelligent tester.

    Main Body (Main Body ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Glass Hatch Opener Switch
    Glass Hatch Opener Switch signal / ON or OFF
    ON: Glass hatch opener switch operates
    OFF: Glass hatch opener switch does not operate
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 7
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

6. INSPECT BACK WINDOW LOCK ASSEMBLY

  1. B172579E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Voltage is not applied between terminals 3 and 4
    10 kΩ or higher
    1 - 2
    Apply battery voltage between terminals 3 and 4
    Below 1 Ω

    If the result is not as specified, replace the back window lock assembly.



NG
REPLACE BACK WINDOW LOCK ASSEMBLY (Click here)
OK


7. INSPECT GLASS HATCH OPENER SWITCH ASSEMBLY

  1. B172580E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Switch free
    10 kΩ or higher
    1 - 2
    Switch pushed
    Below 1 Ω

    If the result is not as specified, replace the glass hatch opener switch assembly.



NG
REPLACE GLASS HATCH OPENER SWITCH ASSEMBLY (Click here)
OK


8. CHECK NO. 2 GLASS HATCH JUNCTION RELAY

  1. A087121E10
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Voltage is not applied between terminals 1 and 2
    Below 1 Ω
    3 - 4
    Apply battery voltage between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Apply battery voltage between terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the No. 2 glass hatch junction relay.



NG
REPLACE NO. 2 GLASS HATCH JUNCTION RELAY
OK


9. CHECK NO. 1 GLASS HATCH JUNCTION RELAY

  1. A087121E10
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Voltage is not applied between terminals 1 and 2
    Below 1 Ω
    3 - 4
    Apply battery voltage between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Apply battery voltage between terminals 1 and 2
    Below 1 Ω

    If the result is not as specified, replace the No. 1 glass hatch junction relay.



NG
REPLACE NO. 1 GLASS HATCH JUNCTION RELAY
OK


10. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - GLASS HATCH OPENER SWITCH)

  1. B172583E03
    Disconnect the D9 and T13 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D9-8 (GHSW) - T13-2 (OPSW)
    Always
    Below 1 Ω
    D9-8 (GHSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - NO. 2 JUNCTION RELAY)

  1. B172582E03
    Disconnect the D6 and O30 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D6-15 (GRY1) - O30-1
    Always
    Below 1 Ω
    D6-15 (GRY1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. CHECK HARNESS AND CONNECTOR (NO. 2 JUNCTION RELAY - NO. 1 JUNCTION RELAY)

  1. B175987E03
    Disconnect the O30 and O29 connectors.Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O30-3 - O29-2
    Always
    Below 1 Ω
    O30-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. CHECK HARNESS AND CONNECTOR (NO. 1 JUNCTION RELAY - MAIN BODY ECU)

  1. B175990E03
    Disconnect the O29 and D6 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O29-1 - D6-26 (GRY2)
    Always
    Below 1 Ω
    O29-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14. CHECK HARNESS AND CONNECTOR (NO. 1 JUNCTION RELAY - BACK WINDOW LOCK)

  1. B175988E04
    Disconnect the O29 and T6 connectors.Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O29-3 - T6-3
    Always
    Below 1 Ω
    O29-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK WINDOW LOCK ASSEMBLY)

  1. B172581E03
    Disconnect the D7 and T6 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D7-20 (GCTY) - T6-2
    Always
    Below 1 Ω
    D7-20 (GCTY) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


← DATA LIST / ACTIVE TEST (from May 2007)Glass Hatch Opener System does not Operate (Aug 2008 – Jun 2010) →