Glass Hatch Opener System does not Operate
Circuit diagnosis · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The glass hatch opener system enables the back door glass to be opened when the glass hatch opener switch is pressed.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. SYSTEM CHECK |
Confirm that the vehicle is equipped with the smart entry and start system.
- Result:
Result
Proceed to
w/ Smart Entry and Start System
A
w/o Smart Entry and Start System
B
|
|
||||
| A | |
| 2. CHECK SMART ENTRY AND START SYSTEM |
When the back door entry lock switch is operated, check that the back door lock.
- OK:
- Back door entry lock function operates normally.
|
|
||||
| OK | |
| 3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Select the item below in the ACTIVE TEST and then check that the relay operates.
Main Body (Main Body ECU): Tester Display
Test Part
Control Range
Diagnostic Note
Glass Hatch Open
Operate Glass Hatch
ON or OFF
-
- OK:
- Glass hatch operates.
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (GLASS HATCH COURTESY SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Select the items below in the DATA LIST, and read the displays on the intelligent tester.
Main Body (Main Body ECU): Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Glass Hatch Courtesy Switch
Glass hatch courtesy switch signal / ON or OFF
ON: Glass hatch is open
OFF: Glass hatch is closed
-
- OK:
- Normal conditions listed above are displayed.
|
|
||||
| OK | |
| 5. READ VALUE USING INTELLIGENT TESTER (GLASS HATCH OPENER SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Select the items below in the DATA LIST, and read the displays on the intelligent tester.
Main Body (Main Body ECU): Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Glass Hatch Opener Switch
Glass Hatch Opener Switch signal / ON or OFF
ON: Glass hatch opener switch operates
OFF: Glass hatch opener switch does not operate
-
- OK:
- Normal conditions listed above are displayed.
|
|
||||
| OK | ||
| ||
| 6. INSPECT BACK WINDOW LOCK ASSEMBLY |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Voltage is not applied between terminals 3 and 4
10 kΩ or higher
1 - 2
Apply battery voltage between terminals 3 and 4
Below 1 Ω
|
|
||||
| OK | |
| 7. INSPECT GLASS HATCH OPENER SWITCH ASSEMBLY |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Switch free
10 kΩ or higher
1 - 2
Switch pushed
Below 1 Ω
|
|
||||
| OK | |
| 8. CHECK NO. 2 GLASS HATCH JUNCTION RELAY |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 4
Voltage is not applied between terminals 1 and 2
Below 1 Ω
3 - 4
Apply battery voltage between terminals 1 and 2
10 kΩ or higher
3 - 5
Voltage is not applied between terminals 1 and 2
10 kΩ or higher
3 - 5
Apply battery voltage between terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 9. CHECK NO. 1 GLASS HATCH JUNCTION RELAY |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 4
Voltage is not applied between terminals 1 and 2
Below 1 Ω
3 - 4
Apply battery voltage between terminals 1 and 2
10 kΩ or higher
3 - 5
Voltage is not applied between terminals 1 and 2
10 kΩ or higher
3 - 5
Apply battery voltage between terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 10. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - GLASS HATCH OPENER SWITCH) |
Disconnect the D9 and T13 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D9-8 (GHSW) - T13-2 (OPSW)
Always
Below 1 Ω
D9-8 (GHSW) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 11. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - NO. 2 JUNCTION RELAY) |
Disconnect the D6 and O30 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D6-15 (GRY1) - O30-1
Always
Below 1 Ω
D6-15 (GRY1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 12. CHECK HARNESS AND CONNECTOR (NO. 2 JUNCTION RELAY - NO. 1 JUNCTION RELAY) |
Disconnect the O30 and O29 connectors.Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
O30-3 - O29-2
Always
Below 1 Ω
O30-3 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 13. CHECK HARNESS AND CONNECTOR (NO. 1 JUNCTION RELAY - MAIN BODY ECU) |
Disconnect the O29 and D6 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
O29-1 - D6-26 (GRY2)
Always
Below 1 Ω
O29-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 14. CHECK HARNESS AND CONNECTOR (NO. 1 JUNCTION RELAY - BACK WINDOW LOCK) |
Disconnect the O29 and T6 connectors.Measure the resistance according to the value(s) in the table below.

- Standard resistance:
Tester Connection
Condition
Specified Condition
O29-3 - T6-3
Always
Below 1 Ω
O29-3 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 15. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BACK WINDOW LOCK ASSEMBLY) |
Disconnect the D7 and T6 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D7-20 (GCTY) - T6-2
Always
Below 1 Ω
D7-20 (GCTY) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
