C1380 Stop Light Control Relay Malfunction
Diagnostic trouble codes · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
Upon receiving the downhill assist control (for 4WD) or hill-start assist control operating signal from the skid control ECU, the relay contact turns on and the stop light comes on.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1380 |
Either of the following is detected:
|
|
WIRING DIAGRAM
Refer to DTC C1425 (Click here).INSPECTION PROCEDURE
- NOTICE:
- When replacing the brake actuator assembly, perform zero point calibration (Click here).
- HINT:
- When C1425 and/or C1426 is output together with C1380, inspect and repair the trouble areas indicated by C1425 and/or C1426 first (Click here, or Click here).
| 1. CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
- OK:
Condition
Illumination Condition
Brake pedal depressed
ON
Brake pedal released
OFF
|
|
||||
| OK | |
| 2. READ VALUE ON INTELLIGENT TESTER (STOP LIGHT SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Select the Data List mode on the intelligent tester (Click here).
ABS / VSC / TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Check that the stop light switch condition observed on the intelligent tester changes according to brake pedal operation.
- OK:
- The intelligent tester displays ON or OFF according to brake pedal operation.
|
|
||||
| OK | |
| 3. INSPECT SKID CONTROL ECU (STP2 TERMINAL) |
Turn the ignition switch off.

Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A24-2 (STP) - A24-22 (STP2)
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT CONTROL RELAY) |
Reconnect the skid control ECU connector.
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Active Test mode on the intelligent tester (Click here).
ABS / VSC / TRC: Tester Display
Test Part
Control Range
Diagnostic Note
Stop Light Relay
Stop light control relay
Relay ON/OFF
Stop lights come on
Check that the "ON" and "OFF" of the stop lights can be shown on the rear combination light by the intelligent tester.
- OK:
- The stop lights turn on or off in accordance with the intelligent tester.
|
|
||||
| OK | |
| 5. RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Perform a road test.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTC (C1380) is not output
A
DTC (C1380) is output
B
|
|
||||
| A | ||
| ||
| 6. INSPECT STOP LIGHT CONTROL RELAY |
Turn the ignition switch off.

Remove the stop light control relay.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 4
Voltage is not applied between terminals 1 and 2
Below 1 Ω
3 - 5
Voltage is not applied between terminals 1 and 2
10 kΩ or higher
3 - 4
Voltage is applied between terminals 1 and 2
10 kΩ or higher
3 - 5
Voltage is applied between terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 7. INSPECT ENGINE ROOM RELAY BLOCK (POWER SOURCE TERMINAL) |
Measure the voltage according to the value(s) in the table below.

- Standard voltage:
Tester Connection
Condition
Specified Condition
Stop light control relay terminal 5 - Body ground
Always
11 to 14 V
Stop light control relay terminal 2 - Body ground
Ignition switch on (IG)
11 to 14 V
|
|
||||
| OK | |
| 8. INSPECT SKID CONTROL ECU (STPO TERMINAL) |
Install the stop light control relay.

Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
A24-31 (STPO) - Body ground
Ignition switch on (IG)
11 to 14 V
|
|
||||
| OK | ||
| ||
| 9. INSPECT SKID CONTROL ECU (STP TERMINAL) |
Turn the ignition switch off.

Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
A24-2 (STP) - Body ground
Stop light switch ON (Brake pedal depressed)
8 to 14 V
A24-2 (STP) - Body ground
Stop light switch OFF (Brake pedal released)
Below 1.5 V
|
|
||||
| OK | ||
| ||
