2007-2013 Highlander Kluger · Service Manual BRAKE

C1381 Acceleration Sensor Power Supply Voltage Malfunction

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.
The yaw rate sensor has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).
If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123 (malfunction in CAN communication with the yaw rate sensor) and U0124 (malfunction in CAN communication with the acceleration sensor) are set.
These DTCs are also output when calibration has not been completed.
DTC Code
DTC Detection Condition
Trouble Area
C1381
At a vehicle speed of more than 3 km/h (2 mph), an acceleration sensor power source malfunction signal is received for 10 seconds or more.
  1. Yaw rate and acceleration sensor power source circuit
  2. Yaw rate and acceleration sensor

WIRING DIAGRAM

Refer to DTCs C1232, C1243 and C1245 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the yaw rate and acceleration sensor, perform zero point calibration (Click here).

HINT:
When U0123, U0124 and/or U0126 is output together with C1381, inspect and repair the trouble areas indicated by U0123, U0124 and/or U0126 first (Click here).


1. INSPECT YAW RATE AND ACCELERATION SENSOR (IG TERMINAL)

  1. C156491E09
    Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the yaw rate and acceleration sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O6-4 (IG) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)
OK


2. INSPECT YAW RATE AND ACCELERATION SENSOR (GND TERMINAL)

  1. C156491E10
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O6-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


3. RECONFIRM DTC
  1. Reconnect the yaw rate and acceleration sensor connector.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 3 km/h (2 mph) or more for at least 10 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC (C1381) is not output
    A
    DTC (C1381) is output
    B

    NOTICE:
    Check the yaw rate and acceleration sensor signal after replacement (Click here).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE YAW RATE AND ACCELERATION SENSOR (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)


← C1380 Stop Light Control Relay Malfunction (from Jul 2010)C1381 Acceleration Sensor Power Supply Voltage Malfunction (Aug 2008 – Jun 2010) →