2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1830/57 Short in Driver Side Curtain Shield Squib Circuit

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010

DESCRIPTION

The driver side curtain shield squib circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly (Driver side).
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side curtain shield squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1830/57
  1. The center airbag sensor assembly receives a line short circuit signal 5 times in the driver side curtain shield squib circuit during primary check.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2 (for LHD)
  2. Floor wire (for RHD)
  3. Curtain shield airbag assembly (Driver side curtain shield squib)
  4. Center airbag sensor assembly
B1831/57
  1. The center airbag sensor assembly receives an open circuit signal in the driver side curtain shield squib circuit for 2 seconds.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2 (for LHD)
  2. Floor wire (for RHD)
  3. Curtain shield airbag assembly (Driver side curtain shield squib)
  4. Center airbag sensor assembly
B1832/57
  1. The center airbag sensor assembly receives a short circuit to ground signal in the driver side curtain shield squib circuit for 0.5 seconds.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2 (for LHD)
  2. Floor wire (for RHD)
  3. Curtain shield airbag assembly (Driver side curtain shield squib)
  4. Center airbag sensor assembly
B1833/57
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the driver side curtain shield squib circuit for 0.5 seconds.
  2. Driver side curtain shield squib malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2 (for LHD)
  2. Floor wire (for RHD)
  3. Curtain shield airbag assembly (Driver side curtain shield squib)
  4. Center airbag sensor assembly

WIRING DIAGRAM

C169773E04

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CONNECTOR

  1. C165141E08
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the curtain shield airbag assembly (Driver side) and center airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the curtain shield airbag assembly (Driver side) and center airbag sensor assembly.

  1. Check that the connector terminals are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the wire harness connector (on the curtain shield airbag assembly (Driver side)) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


2. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY (DRIVER SIDE CURTAIN SHIELD SQUIB)

  1. C168881E02
    Connect the connector to the center airbag sensor assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the curtain shield airbag assembly (Driver side curtain shield squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832, B1833, or 57 is not output.

    HINT:
    Codes other than DTC B1830, B1831, B1832, B1833, and 57 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY (DRIVER SIDE)

3. CHECK WIRE HARNESS (DRIVER SIDE CURTAIN SHIELD SQUIB CIRCUIT)

  1. C157581E05
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      O11-1 (ICL+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      O11-2 (ICL-) - Body ground
      Ignition switch on (IG)
      Below 1 V
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      N8-1 (ICR+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      N8-2 (ICR-) - Body ground
      Ignition switch on (IG)
      Below 1 V

      Result:
      Result
      Proceed to
      OK
      A
      NG (for LHD)
      B
      NG (for RHD)
      C

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      O11-1 (ICL+) - O11-2 (ICL-)
      Always
      Below 1 Ω
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      N8-1 (ICR+) - N8-2 (ICR-)
      Always
      Below 1 Ω

      Result:
      Result
      Proceed to
      OK
      A
      NG (for LHD)
      B
      NG (for RHD)
      C

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      O11-1 (ICL+) - Body ground
      Always
      1 MΩ or higher
      O11-2 (ICL-) - Body ground
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      N8-1 (ICR+) - Body ground
      Always
      1 MΩ or higher
      N8-2 (ICR-) - Body ground
      Always
      1 MΩ or higher

      Result:
      Result
      Proceed to
      OK
      A
      NG (for LHD)
      B
      NG (for RHD)
      C

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      for LHD:
      Tester Connection
      Switch Condition
      Specified Condition
      O11-1 (ICL+) - O11-2 (ICL-)
      Always
      1 MΩ or higher
      for RHD:
      Tester Connection
      Switch Condition
      Specified Condition
      N8-1 (ICR+) - N8-2 (ICR-)
      Always
      1 MΩ or higher

      Result:
      Result
      Proceed to
      OK
      A
      NG (for LHD)
      B
      NG (for RHD)
      C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


4. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C168882E01
    Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the curtain shield airbag assembly (Driver side) and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1830, B1831, B1832, B1833, or 57 is not output.

    HINT:
    Codes other than DTC B1830, B1831, B1832, B1833, and 57 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1830/57 Short in Driver Side Curtain Shield Squib Circuit (+ B1831/57, B1832/57, B1833/57) (May 2007 – Jul 2008)B1835/58 Short in Curtain Shield Squib LH Circuit (+ B1836/58, B1837/58, B1838/58) (from Jul 2010) →