2007-2013 Highlander Kluger · Service Manual STEERING

DIAGNOSTIC TROUBLE CODE CHART

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

HINT:
If a trouble code is displayed during the DTC check, inspect the trouble area listed for that code. For details of the code, refer to the "See page" below.

Power Steering System: 
DTC Code
Detection Item
Trouble Area
Normal Function Return Condition
P/S Warning Light
See page
C1511
Torque Sensor Circuit Malfunction
1. Steering column assembly (Torque sensor)
2. Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1512
Torque Sensor Circuit Malfunction
1. Steering column assembly (Torque sensor)
2. Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1513
Torque Sensor Circuit Malfunction
1. Steering column assembly (Torque sensor)
2. Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1514
Torque Sensor Power Supply Abnormal
1. Steering column assembly (Torque sensor)
2. Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1521
Motor Circuit Malfunction
Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1524
Motor Circuit Malfunction
1. Steering column assembly (Power steering motor)
2. Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1528
Motor Rotation Angle Sensor Malfunction
1. Steering column assembly (Motor rotation angle sensor)
2. Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1531
ECU Malfunction
Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1532
ECU Malfunction
Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1533
ECU Malfunction
Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1534
ECU Malfunction
Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1551
IG Power Supply Voltage Malfunction
1. ECU-IG1 fuse
2. IG power source circuit
3. Power steering ECU
Ignition switch on (IG) again or after normal confirmation
*1
Click here
C1552
PIG Power Supply Voltage Malfunction
1. PIG power source circuit
2. Power steering ECU
Ignition switch on (IG) again or after normal confirmation
*1
Click here
C1554
Power Supply Relay Failure
Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1555
Motor Relay Welding Failure
Power steering ECU
Ignition switch on (IG) again
*1
Click here
C1581
Assist Map Number Un-Writing
Power steering ECU
Assist map write or ignition switch on (IG) again
*1
Click here
U0073
Control Module Communication Bus OFF
CAN communication system
Ignition switch on (IG) again
*1
Click here
U0100
Lost Communication with ECM / PCM "A"
1. CAN communication system
2. ECM
Ignition switch on (IG) again or after normal confirmation
*2
Click here
U0129
Lost Communication with Brake System Control Module
1. CAN communication system
2. Skid control ECU
Ignition switch on (IG) again or after normal confirmation
*1
Click here

HINT:
*1: Warning light comes on
*2: Warning light turns off (normal reset)

← DIAGNOSTIC TROUBLE CODE CHART (Aug 2008 – Jun 2010)ON-VEHICLE INSPECTION (May 2007 – Jul 2008) →