2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Only Wireless Control Function is Inoperative

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher relay signals to the turn signal flasher relay (hazard warning lights).

WIRING DIAGRAM

B176381E03

INSPECTION PROCEDURE


1. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
  1. Check the wireless door lock control system function (Click here).


Result:
Result
Proceed to
The wireless door LOCK/UNLOCK function does not operate with transmitter
A
The power back door function does not operate with transmitter
B
The glass hatch function does not operate with transmitter
C



B
GO TO POWER BACK DOOR SYSTEM (Click here)

C
GO TO GLASS HATCH OPENER SYSTEM (Click here)
A


2. CHECK DOOR CONTROL TRANSMITTER
  1. When another registered door control transmitter is used, check that the wireless operates normally.

    Result:
    Result
    Proceed to
    Wireless door LOCK/UNLOCK function and door control transmitter that did not operate is electrical key transmitter
    A
    Wireless door LOCK/UNLOCK function function does not operate
    B



B
Go to step 5
A


3. CHECK TRANSMITTER LED ILLUMINATION
  1. Check that the transmitter's LED illuminates 3 times when the switch is pressed 3 times.

    Result:
    Result
    Proceed to
    Transmitter's LED does not illuminate 3 times when switch is pressed 3 times
    A
    Transmitter's LED illuminates 3 times when switch is pressed 3 times
    B
    The transmitter's LED does not illuminate the second or third time
    C

    HINT:
    If the transmitter's LED does not illuminate the second or third time, replace the transmitter battery as it is depleted.



B
REPLACE DOOR CONTROL TRANSMITTER

C
REPLACE TRANSMITTER BATTERY (Click here)
A


4. INSPECT TRANSMITTER BATTERY

  1. Electrical key transmitter

    1. Remove the battery from the electrical key transmitter that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal (Click here).B178435E02

      NOTICE:
      Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.

    2. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

    3. Using an oscilloscope, check the transmitter battery voltage waveform.

      HINT:
      Measure the transmitter battery voltage while pressing the LOCK or UNLOCK switch on the transmitter.

      B178436E01

      Standard voltage:
      Item
      Content
      Tester Connection
      Battery positive (+) - Battery negative (-)
      Tool Setting
      0.5 V/DIV., 100 ms/DIV.
      Condition
      Ignition switch OFF, all doors closed and lock switch pushed
      Specified Condition
      2.2 to 3.2 V (Refer to the waveform)



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE DOOR CONTROL TRANSMITTER

5. CHECK ROOM LIGHT ASSEMBLY
  1. Check that the room light illumination operates normally.

    OK:
    Room light operation normally.



NG
Go to LIGHTING SYSTEM (Click here)
OK


6. SWITCH TO SELF-DIAGNOSTIC MODE

  1. B110075E20
    Switch to self-diagnostic mode by operating the ignition key cylinder.
    1. Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.

    2. Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch OFF). Then turn the ignition switch to the ON position and then OFF.

    3. Within 30 seconds of turning the ignition switch OFF, perform the following operation 9 times: turn the ignition switch to the ON position and then OFF.

      NOTICE:
      If the system cannot enter self-diagnostic mode, the system returns to normal mode.

      HINT:
      1. Turning the ignition switch to the ON position after the above operations have been completed ends self-diagnostic mode.
      2. Do not lock or unlock doors during self-diagnostic mode.

  1. Check that the system has switched to self-diagnostic mode by checking the room light flash pattern.

    OK:
    Flash pattern is same as illustration.



NG
Go to step 13
OK


7. CHECK BY SELF DIAGNOSTIC MODE
B123864E03
  1. Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the flash patterns of the room light.

    Result:
    Result
    Proceed to
    Unmatching recognition code is output
    A
    Normal waves (light flash patterns) are output
    B
    No diagnosis outputs
    C



B
REPLACE MAIN BODY ECU

C
Go to step 9
A


8. REGISTER RECOGNITION CODE
  1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered (Click here).

    OK:
    Recognition code can be registered.



NG
Go to step 16
OK

END

9. CHECK DOOR CONTROL RECEIVER (RESPONSE)
  1. Prepare the door control transmitter of another vehicle.

  1. Held down the door control transmitter,s switch.

  1. Check that an unmatching recognition code is output.

    OK:
    Unmatching recognition code is output.



NG
Go to step 10
OK

REPLACE DOOR CONTROL TRANSMITTER

10. REPLACE DOOR CONTROL RECEIVER
  1. Temporarily replace the door lock control receiver with a new or normally functioning one (Click here).


NEXT


11. REGISTER RECOGNITION CODE
  1. Perform the REGISTRATION procedures (Click here).


NEXT


12. CHECK DOOR CONTROL RECEIVER (OPERATION)
  1. Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE MAIN BODY ECU
OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)

13. INSPECT UNLOCK WARNING SWITCH ASSEMBLY

  1. B164411E05
    Remove the unlock warning switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Free
    10 kΩ or higher
    Pushed
    Below 1 Ω

  1. Reconnect the unlock warning switch.



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)
OK


14. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - MAIN BODY ECU AND BODY GROUND)
B175277E04
  1. Disconnect the D16 unlock warning switch connector.

  1. Disconnect the D9 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D16-1 - D9-5 (KSW)
    Always
    Below 1 Ω
    D16-2 - Body ground
    D9-5 (KSW) or D16-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the unlock warning switch connector.

  1. Reconnect the main body ECU connector



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15. CHECK DOOR CONTROL RECEIVER (OUTPUT)

  1. for LHD:

    1. B176377E01
      Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      O28-2 (RDA) - Body ground
      Transmitter switch ON → OFF (No key in ignition key cylinder, all doors closed)
      Below 1 V → 6 to 7 V → Below 1 V

  1. for RHD:

    1. B176378E01
      Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      O38-2 (RDA) - Body ground
      Transmitter switch ON → OFF (No key in ignition key cylinder, all doors closed)
      Below 1 V → 6 to 7 V → Below 1 V



NG
Go to step 16
OK

REPLACE MAIN BODY ECU

16. REPLACE DOOR CONTROL TRANSMITTER
  1. Temporarily replace the door control transmitter module with a new or normally functioning one.


NEXT


17. REGISTER RECOGNITION CODE
  1. Perform the REGISTRATION procedures (Click here).


NEXT


18. CHECK DOOR CONTROL TRANSMITTER MODULE
  1. Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

    OK:
    Doors can be locked and unlocked with transmitter.



NG
REPLACE DOOR CONTROL RECEIVER (Click here)
OK

END (DOOR CONTROL TRANSMITTER MODULE IS DEFECTIVE)


← B1242 Wireless Door Lock Tuner Circuit Malfunction (from Jul 2010)Only Wireless Control Function is Inoperative (Aug 2008 – Jun 2010) →