Only Wireless Control Function is Inoperative
Circuit diagnosis · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher relay signals to the turn signal flasher relay (hazard warning lights).WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS |
Check the wireless door lock control system function (Click here).
- Result:
Result
Proceed to
The wireless door LOCK/UNLOCK function does not operate with transmitter
A
The power back door function does not operate with transmitter
B
The glass hatch function does not operate with transmitter
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK DOOR CONTROL TRANSMITTER |
When another registered door control transmitter is used, check that the wireless operates normally.
- Result:
Result
Proceed to
Wireless door LOCK/UNLOCK function and door control transmitter that did not operate is electrical key transmitter
A
Wireless door LOCK/UNLOCK function function does not operate
B
|
|
||||
| A | |
| 3. CHECK TRANSMITTER LED ILLUMINATION |
Check that the transmitter's LED illuminates 3 times when the switch is pressed 3 times.
- Result:
Result
Proceed to
Transmitter's LED does not illuminate 3 times when switch is pressed 3 times
A
Transmitter's LED illuminates 3 times when switch is pressed 3 times
B
The transmitter's LED does not illuminate the second or third time
C
- HINT:
- If the transmitter's LED does not illuminate the second or third time, replace the transmitter battery as it is depleted.
|
|
||||
|
|
||||
| A | |
| 4. INSPECT TRANSMITTER BATTERY |
Electrical key transmitter
Remove the battery from the electrical key transmitter that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal (Click here).


- NOTICE:
- Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.
Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.
Using an oscilloscope, check the transmitter battery voltage waveform.
- HINT:
- Measure the transmitter battery voltage while pressing the LOCK or UNLOCK switch on the transmitter.


- Standard voltage:
Item
Content
Tester Connection
Battery positive (+) - Battery negative (-)
Tool Setting
0.5 V/DIV., 100 ms/DIV.
Condition
Ignition switch OFF, all doors closed and lock switch pushed
Specified Condition
2.2 to 3.2 V (Refer to the waveform)
|
|
||||
| OK | ||
| ||
| 5. CHECK ROOM LIGHT ASSEMBLY |
Check that the room light illumination operates normally.
- OK:
- Room light operation normally.
|
|
||||
| OK | |
| 6. SWITCH TO SELF-DIAGNOSTIC MODE |
Switch to self-diagnostic mode by operating the ignition key cylinder.

Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.
Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch OFF). Then turn the ignition switch to the ON position and then OFF.
Within 30 seconds of turning the ignition switch OFF, perform the following operation 9 times: turn the ignition switch to the ON position and then OFF.
- NOTICE:
- If the system cannot enter self-diagnostic mode, the system returns to normal mode.
- HINT:
- Turning the ignition switch to the ON position after the above operations have been completed ends self-diagnostic mode.
- Do not lock or unlock doors during self-diagnostic mode.
- Turning the ignition switch to the ON position after the above operations have been completed ends self-diagnostic mode.
Check that the system has switched to self-diagnostic mode by checking the room light flash pattern.
- OK:
- Flash pattern is same as illustration.
|
|
||||
| OK | |
| 7. CHECK BY SELF DIAGNOSTIC MODE |


Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the flash patterns of the room light.
- Result:
Result
Proceed to
Unmatching recognition code is output
A
Normal waves (light flash patterns) are output
B
No diagnosis outputs
C
|
|
||||
|
|
||||
| A | |
| 8. REGISTER RECOGNITION CODE |
Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered (Click here).
- OK:
- Recognition code can be registered.
|
|
||||
| OK | ||
| ||
| 9. CHECK DOOR CONTROL RECEIVER (RESPONSE) |
Prepare the door control transmitter of another vehicle.
Held down the door control transmitter,s switch.
Check that an unmatching recognition code is output.
- OK:
- Unmatching recognition code is output.
|
|
||||
| OK | ||
| ||
| 10. REPLACE DOOR CONTROL RECEIVER |
Temporarily replace the door lock control receiver with a new or normally functioning one (Click here).
| NEXT | |
| 11. REGISTER RECOGNITION CODE |
Perform the REGISTRATION procedures (Click here).
| NEXT | |
| 12. CHECK DOOR CONTROL RECEIVER (OPERATION) |
Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.
- OK:
- Doors can be locked and unlocked with transmitter.
|
|
||||
| OK | ||
| ||
| 13. INSPECT UNLOCK WARNING SWITCH ASSEMBLY |
Remove the unlock warning switch (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Free
10 kΩ or higher
Pushed
Below 1 Ω
Reconnect the unlock warning switch.
|
|
||||
| OK | |
| 14. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - MAIN BODY ECU AND BODY GROUND) |


Disconnect the D16 unlock warning switch connector.
Disconnect the D9 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D16-1 - D9-5 (KSW)
Always
Below 1 Ω
D16-2 - Body ground
D9-5 (KSW) or D16-1 - Body ground
Always
10 kΩ or higher
Reconnect the unlock warning switch connector.
Reconnect the main body ECU connector
|
|
||||
| OK | |
| 15. CHECK DOOR CONTROL RECEIVER (OUTPUT) |
for LHD:
Measure the voltage according to the value(s) in the table below.

- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
O28-2 (RDA) - Body ground
Transmitter switch ON → OFF (No key in ignition key cylinder, all doors closed)
Below 1 V → 6 to 7 V → Below 1 V
for RHD:
Measure the voltage according to the value(s) in the table below.

- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
O38-2 (RDA) - Body ground
Transmitter switch ON → OFF (No key in ignition key cylinder, all doors closed)
Below 1 V → 6 to 7 V → Below 1 V
|
|
||||
| OK | ||
| ||
| 16. REPLACE DOOR CONTROL TRANSMITTER |
Temporarily replace the door control transmitter module with a new or normally functioning one.
| NEXT | |
| 17. REGISTER RECOGNITION CODE |
Perform the REGISTRATION procedures (Click here).
| NEXT | |
| 18. CHECK DOOR CONTROL TRANSMITTER MODULE |
Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.
- OK:
- Doors can be locked and unlocked with transmitter.
|
|
||||
| OK | ||
| ||
