Only Back Door LOCK / UNLOCK Functions do not Operate
Circuit diagnosis · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
- The main body ECU (instrument panel junction block) detects the condition of the back door opener switch.
- The main body ECU (instrument panel junction block) receives signals from the back door opener switch and activates the back door lock motor according to the signals.
- The main body ECU (instrument panel junction block) detects the condition of the back door courtesy switch.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. SYSTEM CHECK |
Check if the vehicle is equipped with a back door closer system.
- Result:
Result
Proceed to
w/ Back Door Closer System
A
w/o Back Door Closer System
B
|
|
||||
| B | |
| 2. READ VALUE USING INTELLIGENT TESTER (BACK DOOR OPENER SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select Back Door Open Handle in the Data List and read the tester display.
Main Body (Main Body ECU): Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Back Door Open Handle
Back door opener switch/ON or OFF
ON: Back door opener switch is pushed
OFF: Back door opener switch is not pushed
-
- OK:
- On the tester screen, the item changes between ON and OFF according to the chart above.
|
|
||||
| OK | |
| 3. INSPECT BACK DOOR LOCK ASSEMBLY |
Remove the back door lock assembly (Click here).

Check operation of the door lock motor.
Move the door lock to the lock position.
Apply battery voltage to the door lock motor and check the operation of the door lock motor.
- OK:
Measurement Condition
Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Unlocked
Check operation of the door courtesy switch.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 3
Locked
10 kΩ or higher
1 - 3
Unlocked
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK CIRCUIT) |
Disconnect the main body ECU (instrument panel junction block) connector.


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
T3-2 (ACT+) - D7-1 (TR+)
Always
Below 1 Ω
T3-2 (ACT+) - Body ground
Always
10 kΩ or higher
T3-3 (D+) - D6-25 (BCTY)
Always
Below 1 Ω
T3-3 (D+) - Body ground
Always
10 kΩ or higher
T3-1 (ACT-) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 5. INSPECT BACK DOOR OPENER SWITCH |
Remove the back door opener switch (Click here).


Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Position
Specified Condition
2 - 3
Back door opener switch not pushed (OFF)
10 kΩ or higher
2 - 3
Back door opener switch pushed (ON)
Below 1 Ω
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH CIRCUIT) |
Disconnect the main body ECU (instrument panel junction block) connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
h1-3 (B) - D7-26 (BDSU)
Always
Below 1 Ω
h1-3 (B) - Body ground
Always
10 kΩ or higher
h1-2 (L) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
