2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Only Back Door LOCK / UNLOCK Functions do not Operate

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

  1. The main body ECU (instrument panel junction block) detects the condition of the back door opener switch.
  2. The main body ECU (instrument panel junction block) receives signals from the back door opener switch and activates the back door lock motor according to the signals.
  3. The main body ECU (instrument panel junction block) detects the condition of the back door courtesy switch.

WIRING DIAGRAM

B171386E02

INSPECTION PROCEDURE


1. SYSTEM CHECK
  1. Check if the vehicle is equipped with a back door closer system.

    Result:
    Result
    Proceed to
    w/ Back Door Closer System
    A
    w/o Back Door Closer System
    B



A
GO TO BACK DOOR CLOSER SYSTEM (Back Door cannot be Opened) (Click here)
B


2. READ VALUE USING INTELLIGENT TESTER (BACK DOOR OPENER SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Select Back Door Open Handle in the Data List and read the tester display.

    Main Body (Main Body ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Open Handle
    Back door opener switch/ON or OFF
    ON: Back door opener switch is pushed
    OFF: Back door opener switch is not pushed
    -

    OK:
    On the tester screen, the item changes between ON and OFF according to the chart above.



NG
Go to step 5
OK


3. INSPECT BACK DOOR LOCK ASSEMBLY

  1. B164421E07
    Remove the back door lock assembly (Click here).

  1. Check operation of the door lock motor.

    1. Move the door lock to the lock position.

    2. Apply battery voltage to the door lock motor and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Unlocked

  1. Check operation of the door courtesy switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      1 - 3
      Locked
      10 kΩ or higher
      1 - 3
      Unlocked
      Below 1 Ω



NG
REPLACE BACK DOOR LOCK ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK CIRCUIT)

  1. Disconnect the main body ECU (instrument panel junction block) connector.B178843E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    T3-2 (ACT+) - D7-1 (TR+)
    Always
    Below 1 Ω
    T3-2 (ACT+) - Body ground
    Always
    10 kΩ or higher
    T3-3 (D+) - D6-25 (BCTY)
    Always
    Below 1 Ω
    T3-3 (D+) - Body ground
    Always
    10 kΩ or higher
    T3-1 (ACT-) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

5. INSPECT BACK DOOR OPENER SWITCH

  1. Remove the back door opener switch (Click here).B171359E04

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    2 - 3
    Back door opener switch not pushed (OFF)
    10 kΩ or higher
    2 - 3
    Back door opener switch pushed (ON)
    Below 1 Ω



NG
REPLACE BACK DOOR OPENER SWITCH (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH CIRCUIT)

  1. B171388E02
    Disconnect the main body ECU (instrument panel junction block) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    h1-3 (B) - D7-26 (BDSU)
    Always
    Below 1 Ω
    h1-3 (B) - Body ground
    Always
    10 kΩ or higher
    h1-2 (L) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


← Only Rear Door RH LOCK / UNLOCK Functions do not Operate (from Jul 2010)Only Back Door LOCK / UNLOCK Functions do not Operate (Aug 2008 – Jun 2010) →