2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Display Signal Circuit between Clock Assembly and Television Camera Assembly

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The display signal from the television camera assembly transmits to the clock assembly.

WIRING DIAGRAM

E210153E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the E9 clock assembly.

  1. Disconnect the T16 television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T16-2 (CV+) - E9-14 (V+)
    Always
    Below 1 Ω
    T16-3 (CGND) - E9-4 (CGND)
    Always
    Below 1 Ω
    T16-4 (CB+) - E9-12 (CA+)
    Always
    Below 1 Ω
    T16-1 (CV-) - E9-15 (V-)
    Always
    Below 1 Ω
    T16-2 (CV+) - Body ground
    Always
    10 kΩ or higher
    T16-3 (CGND) - Body ground
    Always
    10 kΩ or higher
    T16-4 (CB+) - Body ground
    Always
    10 kΩ or higher
    T16-1 (CV-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT CLOCK ASSEMBLY

  1. E153724E11
    Reconnect the E9 clock assembly.
    Text in Illustration 
    *a
    Component with harness connected
    (Clock Assembly)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E9-12 (CA+) - E9-4 (CGND)
    Ignition switch ON
    Shift lever in R
    Approx. 6 V



NG
REPLACE CLOCK ASSEMBLY (Click here)
OK


3. INSPECT TELEVISION CAMERA ASSEMBLY
  1. Reconnect the T16 television camera assembly.

  1. E153724E12
    Check that the E9 connectors are connected to the clock assembly.
    Text in Illustration 
    *a
    Component with harness connected
    (Clock Assembly)

  1. E171712E14
    Check the waveform of the television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.

    OK:
    Waveform is similar to that shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    E9-14 (V+) - E9-5 (GND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch ON, shift lever in R

    HINT:
    The video waveform changes according to the image sent by the television camera assembly.

    Text in Illustration 
    *a
    Waveform 1 (camera lens not covered, displaying an image)
    *b
    Waveform 2 (camera lens covered, blacking out the screen)
    *c
    Synchronization Signal
    *d
    Video Waveform



NG
REPLACE TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Display Signal Circuit between Clock Assembly and Television Camera Assembly (Aug 2008 – Jun 2010)COMPONENTS (from May 2007) →