2007-2013 Highlander Kluger · Service Manual BODY

Rear Window Defogger System does not Operate

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When the rear window defogger switch, which is built into the air conditioning control assembly, is operated, the operation signals are transmitted to the air conditioning amplifier assembly through LIN. When the air conditioning amplifier assembly receives the signals, it turns on the DEFOGGER relay (Marking: RR DEF) to operate the rear window defogger.

WIRING DIAGRAM

B178185E01

INSPECTION PROCEDURE


1. CHECK FUSES (RR DEF)

  1. B165197E03
    Remove the fusible link block assembly (RR DEF) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A - B (RR DEF)
    Always
    Below 1 Ω



NG
REPLACE ENGINE ROOM JUNCTION BLOCK (RR DEF FUSE)
OK


2. INSPECT DEFOGGER RELAY (Marking: RR DEF)

  1. B177582E01
    Remove the defogger relay (Marking: RR DEF) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance 
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Voltage is not applied between terminals 1 and 2
    Below 1 Ω
    3 - 4
    Apply battery voltage between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Apply battery voltage between terminals 1 and 2
    Below 1 Ω



NG
REPLACE DEFOGGER RELAY (Marking: RR DEF)
OK


3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Select the ACTIVE TEST, use the intelligent tester to issue a control command, and then check the window defogger operation.

    Air Conditioner: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Defogger Relay (Rear)
    Rear window defogger
    OFF/ON
    -

    Result:
    Result
    Proceed to
    The window defogger system does not operate normally when operating it through the intelligent tester.
    A
    The window defogger system operates normally when operating it through the intelligent tester.
    B



A
Go to step 7
B


4. CHECK HARNESS AND CONNECTOR (LIN COMMUNICATION LINE)

  1. B175993E02
    Disconnect the D33 air conditioning amplifier connector.

  1. Disconnect the E8 air conditioning control connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D33-37 (LIN1) - E8-5 (LIN1)
    Always
    Below 1 Ω
    D33-37 (LIN1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE AIR CONDITIONING CONTROL ASSEMBLY
  1. for Automatic Air Conditioning System

    1. Replace the air conditioning control assembly (Click here).

  1. for Manual Air Conditioning System

    1. Replace the air conditioning control assembly (Click here).


NEXT


6. CONFIRM REAR WINDOW DEFOGGER OPERATION
  1. Turn the ignition switch on (IG), press the defogger switch, and check that the window defogger operates.

    OK:
    Window defogger system operates normally.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

REPLACE DEFOGGER RELAY (Marking: RR DEF)

7. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Select the ACTIVE TEST, use the intelligent tester to issue a control command, and then check the window defogger operation.

    Air Conditioner: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Defogger Relay (Rear)
    Rear window defogger
    OFF/ON
    -

  1. Check that operation sound of the DEFOGGER relay (Marking: RR DEF) is heard.

    Result:
    Result
    Proceed to
    Relay operating sound is heard
    A
    Relay operating sound is not heard
    B



A
Go to step 10
B


8. CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER ASSEMBLY - ENGINE ROOM RELAY BLOCK)

  1. B175972E02
    Disconnect the D33 air conditioning amplifier connector.

  1. Disconnect the defogger relay (Marking: RR DEF) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D33-38 (RDEF) - 2
    Always
    Below 1 Ω
    D33-38 (RDEF) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK HARNESS AND CONNECTOR (RDEF TERMINAL BATTERY VOLTAGE)

  1. B175992E02
    Reconnect the defogger relay (Marking: RR DEF) from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D33-38 (RDEF) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

10. CHECK HARNESS AND CONNECTOR (REAR WINDOW DEFOGGER WIRE - ENGINE ROOM RELAY BLOCK)

  1. B177576E01
    w/ Glass Hatch Opener:
    1. Disconnect the Y2 connector.

    2. Remove the defogger relay (Marking: RR DEF) from the engine room relay block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Y2-1 - 3
      Always
      Below 1 Ω
      Y2-1 - Body ground
      Always
      10 kΩ or higher

  1. B177575E02
    w/o Glass Hatch Opener:
    1. Disconnect the T12 connector.

    2. Remove the defogger relay (Marking: RR DEF) from the engine room relay block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      T12-1 - 3
      Always
      Below 1 Ω
      T12-1 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. CHECK HARNESS AND CONNECTOR (REAR WINDOW DEFOGGER WIRE CONNECTOR - BODY GROUND)

  1. B177578E01
    w/ Glass Hatch Opener:
    1. Disconnect the Y2 connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Y2-2 - Body ground
      Always
      Below 1 Ω

  1. B177577E01
    w/o Glass Hatch Opener:
    1. Disconnect the T11 connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      T11-1 - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE REAR WINDOW DEFOGGER WIRE


← Rear Window Defogger System does not Operate (Aug 2008 – Jun 2010)ON-VEHICLE INSPECTION (May 2007 – Jun 2010) →