2007-2013 Highlander Kluger · Service Manual ENGINE

P0335 Crankshaft Position Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

Versions by build date: May 2007 – Jun 2010 from Jul 2010

DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and a magnet.
The sensor plate rotates as each tooth passes through the pickup coil, and a pulse signal is created. The pickup coil generates 34 signals per engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.
DTC No.
DTC Detection Condition
Trouble Area
P0335
  1. No crankshaft position sensor signal to ECM while cranking (1 trip detection logic)
  2. No crankshaft position sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic)
  3. Missing crankshaft position sensor signal despite VVT sensor signal inputs normal after engine cranked ( 1 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Sensor plate (crankshaft position sensor plate)
  4. ECM
P0339
Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed 1000 rpm or more
(b) Starter signal OFF
(c) 3 seconds or more have lapsed since starter signal switched from ON to OFF
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Sensor plate (crankshaft position sensor plate)
  4. ECM
Reference: Inspection using an oscilloscope
A196825E04

HINT:
  1. The correct waveform is shown in the illustration.
  2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the crankshaft position sensor signal.
    Item
    Content
    Terminals
    VV1+ - VV1-
    VV2+ - VV2-
    NE+ - NE-
    Equipment Settings
    5 V/DIV., 20 ms./DIV.
    Conditions
    Idling


WIRING DIAGRAM

A241531E01

INSPECTION PROCEDURE

HINT:
  1. After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 and/or P0339 are output again, check the following items related to the camshaft position sensor.
    1. Installation condition of the camshaft position sensor
    2. Installation condition of the camshaft
    3. Connection of the camshaft position sensor connector
  2. If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
  3. The engine speed can be checked by using the intelligent tester. To perform the check, follow the procedures below:
    1. Connect the intelligent tester to the DLC3.
    2. Start the engine.
    3. Turn the tester on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
    2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)

  1. A148718E15
    Disconnect the crankshaft position sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Cold
    1630 to 2740 Ω
    1 - 2
    Hot
    2065 to 3225 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Crankshaft Position Sensor)

    HINT:
    Terms "cold" and "hot" refer to the temperature of the coils. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).

  1. Reconnect the crankshaft position sensor connector.



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance :
    Check for open:
    Tester Connection
    Condition
    Specified Condition
    B21-1 - B50-6 (NE+)
    Always
    Below 1 Ω
    B21-2 - B50-5 (NE-)
    Always
    Below 1 Ω
    Check for short:
    Tester Connection
    Condition
    Specified Condition
    B21-1 or B50-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B21-2 or B50-5 (NE-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the crankshaft position sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
OK


3. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

  1. BR03795E54
    Check the crankshaft position sensor installation condition.

    OK:
    Sensor is installed correctly.



NG
REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


4. CHECK CRANKSHAFT (TEETH OF CRANKSHAFT ANGLE SENSOR PLATE)
  1. Remove the crankshaft angle sensor plate (Click here).

  1. Check the teeth of the crankshaft angle sensor plate.

    OK:
    Crankshaft angle sensor plate does not have any cracks or deformation.

  1. Reinstall the crankshaft angle sensor plate (Click here).



NG
REPLACE CRANKSHAFT (CRANKSHAFT ANGLE SENSOR PLATE) (Click here)
OK

REPLACE ECM (Click here)


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (May 2007 – Jun 2010)P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (+ 5 more codes) (May 2007 – Jun 2010) →