2007-2013 Highlander Kluger · Service Manual ENGINE

P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built May 2007 – Jun 2010

Also covers:

Versions by build date: May 2007 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013

DESCRIPTION

The VVT sensor (G signal) consists of a magnet and magneto resistance element.
The exhaust camshaft has 3 teeth on its inner circumference. When the camshaft gear rotates, the air gap changes between the protrusion on the gear and the pickup coil. The change affects the magnetic field, resulting in a change in the resistance of the magneto resistance element. The crankshaft angle sensor plate has 34 teeth and outputs 34 signals every engine revolution. The ECM detects the standard crankshaft angle based on the G signal, actual crankshaft angle and engine speed by an NE signal.
DTC No.
DTC Detection Condition
Trouble Area
P0340
P0345
  1. Input voltage to ECM remains 0.3 V or less, or 4.7 V or higher for more than 5 seconds, when 2 or more seconds have elapsed after turning ignition switch ON (2 trip detection logic)
  2. No VVT sensor signal to ECM during cranking (1 trip detection logic)
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Camshaft timing pulley
  4. Jumped tooth of timing chain
  5. ECM
P0342
P0347
Output voltage of VVT sensor is 0.3 V or less for 5 seconds (1 trip detection logic)
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Camshaft timing pulley
  4. Jumped tooth of timing chain
  5. ECM
P0343
P0348
Output voltage of VVT sensor is 4.7 V or more for 5 seconds (1 trip detection logic)
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Camshaft timing pulley
  4. Jumped tooth of timing chain
  5. ECM
Reference: Inspection using an oscilloscope
A107148E09

HINT:
  1. The correct waveform is shown in the illustration.
  2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the crankshaft position sensor signal.
    Item
    Content
    Terminals
    NE+ - NE-
    VV1+ - VV1-
    VV2+ - VV2-
    Equipment Settings
    5 V/DIV., 20 ms./DIV.
    Conditions
    Cranking or idling


WIRING DIAGRAM

Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

  1. A168209E02
    Disconnect the VVT sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B22-1 (VVT sensor) - B3-19 (VV1+)
    Always
    Below 1 Ω
    B22-2 (VVT sensor) - B3-29 (VV1-)
    Always
    Below 1 Ω
    B22-3 (VVT sensor) - B1-23 (VC)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B23-1 (VVT sensor) - B3-18 (VV2+)
    Always
    Below 1 Ω
    B23-2 (VVT sensor) - B3-28 (VV2-)
    Always
    Below 1 Ω
    B23-3 (VVT sensor) - B1-23 (VC)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B22-1 (VVT sensor) or B3-19 (VV1+) - Body ground
    Always
    10 kΩ or higher
    B22-2 (VVT sensor) or B3-29 (VV1-) - Body ground
    Always
    10 kΩ or higher
    B22-3 (VVT sensor) or B1-23 (VC) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B23-1 (VVT sensor) or B3-18 (VV2+) - Body ground
    Always
    10 kΩ or higher
    B23-2 (VVT sensor) or B3-28 (VV2-) - Body ground
    Always
    10 kΩ or higher
    B23-3 (VVT sensor) or B1-23 (VC) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VVT sensor connector.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK VVT SENSOR (SENSOR POWER SOURCE)

  1. A168210E05
    Disconnect the VVT sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - Body ground
    Ignition switch on (IG)
    4.5 to 5.0 V

  1. Reconnect the VVT sensor connector.



NG
REPLACE ECM (Click here)
OK


3. CHECK SENSOR INSTALLATION (VVT SENSOR)

  1. BR03795E54
    Check the VVT sensor installation condition.

    OK:
    Sensor is installed correctly.



NG
REPAIR OR REPLACE VVT SENSOR
OK


4. CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)
  1. Check the teeth of the signal plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
OK


5. REPLACE VVT SENSOR
  1. Replace the VVT sensor (Click here).


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Clear the DTCs.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P0340, P0342, P0343, P0345, P0347, or P0348
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (from Jul 2010)P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (+ 5 more codes) (Jul 2010 – Jul 2013) →