2007-2013 Highlander Kluger · Service Manual ENGINE

P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)

Diagnostic trouble codes · Vehicles built from Aug 2013

Also covers:

Versions by build date: May 2007 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013

DESCRIPTION

The intake camshaft's VVT sensor (G signal) consists of a magnet and Magnetic Resistance Element (MRE).
The camshaft timing gear has a sensor plate with 3 teeth on its outer circumference. When the gear rotates, changes occur in the air gaps between the sensor plate and magneto resistance element, which affects the magnetic field. As a result, the resistance of the magneto resistance element material fluctuates. The VVT sensor converts the gear rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
Then the ECM uses this data to control fuel injection time and injection timing.
DTC No.
DTC Detection Condition
Trouble Area
P0340
Either of the following condition is met:
  1. Missing VVT sensor signal despite crankshaft position sensor inputs normal at engine speed of 600 rpm or more (1 trip detection logic)
  2. No VVT sensor signal to ECM during cranking (2 trip detection logic)
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Camshaft timing gear for intake camshaft
  4. Jumped tooth of timing chain for intake camshaft
  5. ECM
P0342
P0347
Output voltage of VVT sensor is less than 0.3 V for 4 seconds (1 trip detection logic)
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Camshaft timing gear for intake camshaft
  4. Jumped tooth of timing chain for intake camshaft
  5. ECM
P0343
P0348
Output voltage of VVT sensor is more than 4.7 V for 4 seconds (1 trip detection logic)
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Camshaft timing gear for intake camshaft
  4. Jumped tooth of timing chain for intake camshaft
  5. ECM
P0345
No VVT sensor signal at engine speed of 600 rpm or more (1 trip detection logic)
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Camshaft timing gear for intake camshaft
  4. Jumped tooth of timing chain for intake camshaft
  5. ECM
Reference: Inspection using an oscilloscope
A107148E09

HINT:
  1. The correct waveform is shown in the illustration.
  2. VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the crankshaft position sensor signal.
    Item
    Content
    Terminals
    NE+ - NE-
    VV1+ - VV1-
    VV2+ - VV2-
    Equipment Settings
    5 V/DIV., 20 ms./DIV.
    Conditions
    Idling


WIRING DIAGRAM

Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

HINT:
  1. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  2. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  3. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)

  1. A168210E20
    Disconnect the VVT sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Bank 1:
    Tester Connection
    Switch Condition
    Specified Condition
    B22-3 (VC) - Body ground
    Ignition switch on (IG)
    4.5 to 5.0 V
    Bank 2:
    Tester Connection
    Switch Condition
    Specified Condition
    B23-3 (VC) - Body ground
    Ignition switch on (IG)
    4.5 to 5.0 V

    Text in Illustration 
    *1
    Bank 1
    *2
    Bank 2
    *a
    Front view of wire harness connector
    (to VVT Sensor for Intake Camshaft)

  1. Reconnect the VVT sensor connector.



NG
Go to step 7
OK


2. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
  1. Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B22-1 (VVR+) - B50-9 (VV1+)
    Always
    Below 1 Ω
    B22-2 (VVR-) - B50-10 (VV1-)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B23-1 (VVL+) - B50-12 (VV2+)
    Always
    Below 1 Ω
    B23-2 (VVL-) - B50-11 (VV2-)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B22-1 (VVR+) or B50-9 (VV1+) - Body ground
    Always
    10 kΩ or higher
    B22-2 (VVR-) or B50-10 (VV1-) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B23-1 (VVL+) or B50-12 (VV2+) - Body ground
    Always
    10 kΩ or higher
    B23-2 (VVL-) or B50-11 (VV2-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VVT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT SENSOR - ECM)
OK


3. CHECK SENSOR INSTALLATION (VVT SENSOR)

  1. BR03795E54
    Check the VVT sensor installation condition.

    OK:
    Sensor is installed correctly.



NG
REPAIR OR REPLACE VVT SENSOR (Click here)
OK


4. CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)
OK


5. REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT)
  1. Replace the VVT sensor for intake camshaft (Click here).


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs.

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and turn the tester on.

  1. Start the engine.

  1. Idle the engine for 10 seconds or more.

  1. Select the following menu items: Powertrain / Engine and ECT / DTC / Pending.

  1. Read the pending DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    P0340, P0342, P0343, P0345, P0347 or P0348
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END

7. CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
  1. Disconnect the VVT sensor for intake camshaft connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B22-3 (VC) - B50-15 (VCV1)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B23-3 (VC) - B50-16 (VCV2)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B22-3 (VC) or B50-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B23-3 (VC) or B50-16 (VCV2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VVT sensor for intake camshaft connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT SENSOR - ECM)
OK

REPLACE ECM (Click here)


← P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (+ 5 more codes) (Jul 2010 – Jul 2013)P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 5 more codes) (May 2007 – Jul 2008) →