2007-2013 Highlander Kluger · Service Manual ENGINE

P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)

Diagnostic trouble codes · Vehicles built Jul 2010 – Jul 2013

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013

CAUTION / NOTICE / HINT

HINT:
If DTC P0011, P0012, P0021 or P0022 is present, check the VVT (Variable Valve Timing) system.


DESCRIPTION

Refer to DTC P0010 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P0011
P0021
Valve timing is not adjusted in valve timing advance range
(1 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve assembly for intake camshaft (bank 1, 2)
  3. Oil control valve filter
  4. Intake camshaft timing gear assembly (bank 1, 2)
  5. ECM
P0012
P0022
Valve timing is not adjusted in valve timing retard range
(2 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve assembly for intake camshaft (bank 1, 2)
  3. Oil control valve filter
  4. Intake camshaft timing gear assembly (bank 1, 2)
  5. ECM

WIRING DIAGRAM

Refer to DTC P0010 (Click here).

INSPECTION PROCEDURE

Abnormal bank
Advanced timing over
(Valve timing is out of specified range)
Retarded timing over
(Valve timing is out of specified range)
Bank 1
P0011
P0012
Bank 2
P0021
P0022

HINT:
  1. If DTC P0011 or P0012 is displayed, check the bank 1 VVT system circuit.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  4. If DTC P0021 or P0022 is displayed, check the bank 2 VVT system circuit.
  5. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0011, P0012, P0021 or P0022
    A
    P0011, P0012, P0021 or P0022 and other DTCs
    B

    HINT:
    If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OIL CONTROL VALVE FOR INTAKE CAMSHAFT)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).

  1. Check the engine speed while operating the camshaft timing oil control valve assembly using the tester.

    OK:
    Tester Operation
    Specified Condition
    0%
    Normal engine idle speed
    100%
    Engine idles roughly or stalls



NG
Go to step 4
OK


3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  1. Idle the engine for 3 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  1. Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Depress the accelerator pedal by a large amount.

  1. Idle the engine for 3 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the pending DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC P0011, P0012, P0021 or P0022 is output
    B

    HINT:
    DTC P0011, P0012, P0021 or P0022 may be stored when foreign objects in engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.



B
Go to step 4
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)

  1. A135015E04
    Remove the cylinder head covers RH and LH.

  1. Turn the crankshaft to align the timing marks of the crankshaft.

  1. Align the notch of the crankshaft pulley to the "0" position.

  1. Check if the timing marks of the camshaft pulley and camshaft bearing cap align.

  1. Turn the crankshaft clockwise by 360° if the timing marks do not align. Check if they align once again.

    OK:
    The timing marks of the camshaft pulley and the camshaft bearing cap align when the notch of the crankshaft pulley is in the "0" position.

    Text in Illustration 
    *1
    Timing Mark



NG
ADJUST VALVE TIMING (Click here)
OK


5. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

  1. A233347E01
    Remove the camshaft timing oil control valve assembly (for intake camshaft).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft))

  1. A231241E02
    Connect the positive (+) battery terminal to terminal 1 and connect the negative (-) battery terminal to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the camshaft timing oil control valve assembly (for intake camshaft).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


6. CHECK OIL PIPE AND OIL CONTROL VALVE FILTER

  1. G042497E04
    Remove the oil pipe No. 1 or oil pipe assembly.

  1. Remove the oil control valve filter.

  1. Check that the filter and pipe are not clogged.

    OK:
    The filter and pipe are not clogged.

    Text in Illustration 
    *1
    Bank 1
    *2
    Bank 2



NG
REPLACE OIL CONTROL VALVE FILTER OR PIPE (Click here)
OK


7. REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
  1. Replace the camshaft timing gear assembly for intake camshaft (Click herefor Bank 1, Click here for bank 2).


NEXT


8. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  1. Idle the engine for 3 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  1. Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Depress the accelerator pedal by a large amount.

  1. Idle the engine for 3 minutes or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the pending DTCs.

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC P0011, P0012, P0021 or P0022 is output
    B



B
REPLACE ECM (Click here)
A

END


← P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (+ P0012, P0021, P0022) (Aug 2008 – Jun 2010)P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) (+ P0012, P0021, P0022) (from Aug 2013) →