2007-2013 Highlander Kluger · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY

HINT:
Refer to the instructions for REMOVAL of the parking brake pedal (Click here).


2. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY

  1. C165703
    Remove the adjusting nut.

  1. C165704
    Remove the clip.

  1. C165705
    Pull up the parking brake pedal claw and remove the No. 1 parking brake cable assembly.


3. REMOVE REAR WHEEL

4. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for 2WD)

  1. C167785
    Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.


5. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for 4WD)

  1. C165996
    Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.


6. REMOVE REAR DISC

  1. C166438E01
    Put matchmarks on the rear disc and the axle hub.

  1. D028126
    Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.


7. REMOVE NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING

  1. C166147
    Remove the 2 No. 1 parking brake shoe return tension springs.


8. SEPARATE NO. 1 PARKING BRAKE SHOE ASSEMBLY

  1. C166148
    Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 1 parking brake shoe assembly from the backing plate.


9. REMOVE PARKING BRAKE SHOE STRUT

  1. C166149
    Remove the parking brake shoe strut and the parking brake shoe strut compression spring.


10. SEPARATE NO. 2 PARKING BRAKE SHOE ASSEMBLY

  1. C166150
    Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 2 parking brake shoe assembly from the backing plate.


11. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET

  1. C166151
    Remove the parking brake shoe adjusting screw set.


12. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY

  1. C166152
    Separate the No. 2 parking brake shoe return tension spring and remove the No. 1 parking brake shoe assembly.


13. REMOVE NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING

  1. C166153
    Remove the No. 2 parking brake shoe return tension spring from the No. 2 parking brake shoe assembly.


14. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER

  1. C166154
    Using needle-nose pliers, separate the No. 3 parking brake cable assembly from the parking brake shoe lever as shown in the illustration.

    NOTICE:
    Be careful not to damage the No. 3 parking brake cable assembly.


15. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

  1. C166156
    Remove the 2 bolts and separate the No. 3 parking brake cable assembly from the backing plate.

  1. Remove the 2 bolts, 4 nuts, and the No. 3 parking brake cable assembly.

    C166164


16. REMOVE CABLE SUPPORT BRACKET

  1. Remove the cable support bracket from the No. 3 parking brake cable assembly.

    C165719


17. REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY

  1. C168094
    Remove the 2 bolts and separate the No. 2 parking brake cable assembly from the backing plate.

  1. Remove the 2 bolts, 5 nuts, and the No. 2 parking brake cable assembly.

    C165718


18. REMOVE PARKING BRAKE CABLE SUPPORT BRACKET

  1. Remove the parking brake cable support bracket from the No. 2 parking brake cable assembly.

    C166584


19. REMOVE NO. 1 PARKING BRAKE CABLE SUPPORT BRACKET

  1. Remove the No. 1 parking brake cable support bracket from the No. 2 parking brake cable assembly.

    C166585

← COMPONENTS (from May 2007)REMOVAL (Aug 2008 – Jun 2010) →