2007-2013 Highlander Kluger · Service Manual ENGINE

ECM Power Source Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When the ignition switch is turned to on (IG), battery voltage is applied to IGSW of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil, closing the contacts of the engine room junction block assembly (EFI relay) and supplying power to terminal +B and +B2 of the ECM.

WIRING DIAGRAM

A173972E12
A242258E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B48-12 (E1) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BODY GROUND)
OK


2. CHECK ECM (IGSW VOLTAGE)

  1. A205277E21
    Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D55-21 (IGSW) - Body ground
    Ignition switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)

  1. Reconnect the ECM connector.



NG
Go to step 7
OK


3. CHECK ECM (+B AND +B2 TERMINAL VOLTAGE)

  1. A205277E27
    Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D56-22 (+B) - B48-12 (E1)
    Ignition switch on (IG)
    11 to 14 V
    D56-23 (+B2) - B48-12 (E1)
    Ignition switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 4
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

4. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (EFI RELAY)
  1. Inspect the engine room junction block assembly (Click here).



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY (EFI RELAY) (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (EFI RELAY - ECM)
  1. Remove the engine room junction block assembly from the engine room relay block.

  1. Disconnect the engine room junction block assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    2E-6 - D56-22 (+B)
    Always
    Below 1 Ω
    2E-6 - D56-23 (+B2)
    Always
    Below 1 Ω
    2E-9 - D56-9 (MREL)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    2E-6 or D56-22 (+B) or D56-23 (+B2) - Body ground
    Always
    10 kΩ or higher
    2E-9 or D56-9 (MREL) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the engine room junction block assembly connector.

  1. Reinstall the engine room junction block assembly.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI RELAY - ECM)
OK


6. CHECK HARNESS AND CONNECTOR (EFI RELAY - BODY GROUND)
  1. Remove the engine room junction block assembly from the engine room relay block.

  1. Disconnect the engine room junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    2E-10 - Body ground
    Always
    Below 1 Ω

  1. Reconnect the engine room junction block assembly connector.

  1. Reinstall the engine room junction block assembly.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI RELAY - BODY GROUND)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI RELAY - BATTERY)

7. INSPECT IG2 RELAY

  1. A234567E01
    Remove the IG2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    No battery voltage applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω

  1. Reinstall the IG2 relay.



NG
REPLACE IG2 RELAY
OK


8. CHECK HARNESS AND CONNECTOR (IG2 RELAY - ECM)
  1. Disconnect the ECM connector.

  1. Remove the IG2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    IG2 relay terminal 3 - D55-21 (IGSW)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    IG2 relay terminal 3 or D55-21 (IGSW) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reinstall the IG2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - ECM)
OK


9. CHECK HARNESS AND CONNECTOR (IG2 RELAY POWER SOURCE)

  1. A172712E04
    Remove the IG2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block

  1. Reinstall the IG2 relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - BATTERY)
OK


10. CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)
  1. Remove the IG2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    IG2 relay terminal 2 - Body ground
    Always
    Below 1 Ω

  1. Reinstall the IG2 relay.

    Result:
    Result
    Proceed to
    OK (w/ smart entry and start system)
    A
    OK (w/o smart entry and start system)
    B
    NG
    C



B
Go to step 12

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - BODY GROUND)
A


11. CHECK HARNESS AND CONNECTOR (IG2 RELAY - MAIN BODY ECU)
  1. Remove the IG2 relay from the engine room relay block.

  1. Disconnect the main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    IG2 relay terminal 1 - D6-11 (IG2D)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    IG2 relay terminal 1 or D6-11 (IG2D) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the IG2 relay.

  1. Reconnect the main body ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - MAIN BODY ECU)
OK

CHECK SMART ENTRY AND START SYSTEM (Click here)

12. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - IG2 RELAY)
  1. Remove the IG2 relay from the engine room relay block.

  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D21-6 (IG2) - IG2 relay terminal 1
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D21-6 (IG2) or IG2 relay terminal 1 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the IG2 relay.

  1. Reconnect the ignition switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - IG2 RELAY)
OK


13. INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly (Click here).



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)


← ECM Power Source Circuit (Aug 2008 – Jun 2010)VC Output Circuit (May 2007 – Jul 2008) →