2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

DATA LIST / ACTIVE TEST

System information · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Enter the following menus: Body / MAIN BODY or Entry&Start / Data List.

  4. Read the Data List according to the display on the tester.

    MAIN BODY (Main body ECU):  
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Wireless Control
    Wireless door lock control function / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    Hazard Answer Back
    Hazard answer-back of wireless / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    Open Door Warning*
    Open door warning / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    Unlock 2 Operation*
    Unlock 2 Operation of wireless unlock / ON or OFF
    ON: All doors unlock when UNLOCK switch pressed twice
    OFF: All doors unlock when UNLOCK switch pressed once
    -
    Auto Lock Time
    Automatic lock time / 120 s, 60 s or 30 s
    120 s: 120 seconds
    60 s: 60 seconds
    30 s: 30 seconds
    -
    Wireless Buzzer Resp*
    Wireless door lock buzzer response / ON or OFF
    ON: Operating
    OFF: Not operating
    -

    HINT:
    *: for RHD

    Entry&Start (Certification ECU (Smart Key ECU Assembly)):  
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Panic Alarm Function*
    Panic function / ON or OFF
    ON: Operating
    OFF: Not operating
    -

    HINT:
    *: for RHD


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing the Active Test early in troubleshooting is one way to save diagnostic time. The Data List can be displayed during the Active Test.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Enter the following menus: Body / MAIN BODY or Entry&Start / Active Test.

  4. Perform the Active Test according to the display on the tester.

    MAIN BODY (Main body ECU): 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Hazard
    Turns the turn signal flasher relay
    ON/OFF
    Observe headlight and rear combination light for correct operation
    Vehicle Horn*
    Turns the vehicle horns
    ON/OFF
    -
    Illuminated Entry System
    Interior light and ignition key cylinder light (Interior light switch is in DOOR position and all doors are closed)
    ON/OFF
    -
    Trunk and Back-Door Open
    Turns the back door opener motor
    ON/OFF
    Observe back door
    Entry&Start (Certification ECU (Smart Key ECU Assembly)): 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Wireless Buzzer Operation*
    Turns the wireless door lock buzzer
    ON/OFF
    -

    HINT:
    *: for RHD

← DTC CHECK / CLEAR (from May 2007)DATA LIST / ACTIVE TEST (from Jul 2010) →