2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1622/81 Lost Communication with Driver Side - Side Airbag Sensor Assembly

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010

DESCRIPTION

The driver side - side collision sensor circuit (to determine deployment of the front seat side airbag assembly (Driver side) and curtain shield airbag assembly (Driver side)) is composed of the center airbag sensor assembly, side airbag sensor (Driver side), and rear airbag sensor (Driver side).
The side airbag sensor (Driver side) and rear airbag sensor (Driver side) detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1622/81, B1623/81, B1632/81, B1633/81, B1642/81, or B1643/81 is recorded when a malfunction is detected in the driver side - side collision sensor circuit (to determine deployment of the front seat side airbag assembly (Driver side) and curtain shield airbag assembly (Driver side)).
DTC No.
DTC Detection Condition
Trouble Area
B1622/81
B1623/81
B1632/81
B1633/81
B1642/81
B1643/81
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the driver side - side collision sensor (Driver side) circuit (to determine deployment of the front seat side airbag assembly (Driver side) and curtain shield airbag assembly (Driver side)) for 2 seconds.
  1. Side airbag sensor (Driver side) malfunction
  1. Rear airbag sensor (Driver side) malfunction
  1. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Side airbag sensor (Driver side)
  4. Rear airbag sensor (Driver side)
  5. Center airbag sensor assembly

WIRING DIAGRAM

C169772E01

INSPECTION PROCEDURE


1. CHECK PRESENT DTC

  1. C157627E03
    Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for present DTCs (Click here).

    Result:
    Result
    Proceed to
    Present DTC B1623 or B1643 is output.
    A
    Present DTC B1642 or 81 is output.
    B
    Present DTC B1632 or B1633 is output.
    C
    Present DTC B1622 is output.
    D
    Present DTC B1622, B1623, B1632, B1633, B1642, B1643 or 81 is not output.
    E

    HINT:
    1. DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then on (IG) again.
    2. Codes other than present DTC B1622, B1623, B1632, B1633, B1642, B1643, and 81 may be output at this time, but they are not related to this check.



B
Go to step 3

C
Go to step 14

D
Go to step 21

E
USE SIMULATION METHOD TO CHECK (Click here)
A


2. CHECK PAST DTC
  1. Check for past DTCs (Click here).

    Result:
    Result
    Proceed to
    Past DTC B1622 or B1632 is not output.
    A
    Past DTC B1632 is output.
    B
    Past DTC B1622 is output.
    C

    HINT:
    Codes other than past DTC B1622 and B1632 may be output at this time, but they are not related to this check.



B
Go to step 14

C
Go to step 21
A


3. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly, rear airbag sensor (Driver side) and the side airbag sensor (Driver side).

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly, rear airbag sensor (Driver side) and side airbag sensor (Driver side).

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


4. CHECK WIRE HARNESS (OPEN)

  1. Using SST, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.C157706E02

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-4 (BBL+) - O3-3 (BBL-)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-4 (BBR+) - N3-3 (BBR-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


5. CHECK WIRE HARNESS (SHORT)

  1. C157707E02
    Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-4 (BBL+) - O3-3 (BBL-)
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-4 (BBR+) - N3-3 (BBR-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


6. CHECK WIRE HARNESS (SHORT TO B+)

  1. C157707E02
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-4 (BBL+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O3-3 (BBL-) - Body ground
    Ignition switch on (IG)
    Below 1 V
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-4 (BBR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N3-3 (BBR-) - Body ground
    Ignition switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


7. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C157707E02
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified cCondition
    O3-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    O3-3 (BBL-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    N3-3 (BBR-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


8. CHECK WIRE HARNESS (OPEN)

  1. Using SST, connect terminals 2 (LHD: (BCL+), RHD: (BCR+)) and 1 (LHD: (BCL-), RHD: (BCR-)) of connector C.C157704E03

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - O3-2 (BCL-)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - N3-2 (BCR-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


9. CHECK WIRE HARNESS (SHORT)

  1. C157705E03
    Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - O3-2 (BCL-)
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - N3-2 (BCR-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


10. CHECK WIRE HARNESS (SHORT TO B+)

  1. C157705E03
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O3-2 (BCL-) - Body ground
    Ignition switch on (IG)
    Below 1 V
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N3-2 (BCR-) - Body ground
    Ignition switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


11. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C157705E03
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    O3-2 (BCL-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    N3-2 (BCR-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


12. CHECK SIDE AIRBAG SENSOR (DRIVER SIDE)

  1. C171002E02
    Connect the connector to the rear airbag sensor (Driver side) and center airbag sensor assembly.

  1. Interchange the side airbag sensor (Passenger side) with the side airbag sensor (Driver side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1623, B1642, B1643, or 81 is output.
    A
    DTC B1628, B1647, B1648, or 82 is output.
    B
    DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 are not output.
    C

    HINT:
    Codes other than DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR (DRIVER SIDE) (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


13. CHECK REAR AIRBAG SENSOR (DRIVER SIDE)

  1. C167953E03
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor (Passenger side) and side airbag sensor (Driver side) to their original positions and connect the connectors to them.

  1. Interchange the rear airbag sensor (Passenger side) with the rear airbag sensor (Driver side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 are not output.
    A
    DTC B1623, B1642, B1643, or 81 is output.
    B
    DTC B1628, B1647, B1648, or 82 is output.
    C

    HINT:
    Codes other than DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR (DRIVER SIDE) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

14. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor (Driver side) and rear airbag sensor (Driver side).

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the side airbag sensor (Driver side) and rear airbag sensor (Driver side).

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


15. CHECK WIRE HARNESS (OPEN)

  1. Using SST, connect terminals 2 (LHD: (BCL+), RHD: (BCR+)) and 1 (LHD: (BCL-), RHD: (BCR-)) of connector C.C157704E03

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - O3-2 (BCL-)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - N3-2 (BCR-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


16. CHECK WIRE HARNESS (SHORT)

  1. C157705E03
    Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - O3-2 (BCL-)
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - N3-2 (BCR-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


17. CHECK WIRE HARNESS (SHORT TO B+)

  1. C157705E03
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O3-2 (BCL-) - Body ground
    Ignition switch on (IG)
    Below 1 V
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N3-2 (BCR-) - Body ground
    Ignition switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


18. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C157705E03
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    O3-2 (BCL-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    N3-2 (BCR-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


19. CHECK SIDE AIRBAG SENSOR (DRIVER SIDE)

  1. C166120E02
    Connect the connector to the rear airbag sensor.

  1. Interchange the side airbag sensor (Passenger side) with the side airbag sensor (Driver side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1632 or B1633 is output.
    A
    DTC B1637 or B1638 is output.
    B
    DTC B1632 or B1633 and B1637 or B1638 are not output.
    C

    HINT:
    Codes other than DTC B1632 or B1633 and B1637 or B1638 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR (DRIVER SIDE) (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


20. CHECK REAR AIRBAG SENSOR (DRIVER SIDE)

  1. C166174E05
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor (Passenger side) and side airbag sensor (Driver side) to their original positions and connect the connectors to them.

  1. Interchange the rear airbag sensor (Passenger side) with the rear airbag sensor (Driver side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1632 or B1633 and B1637 or B1638 are not output.
    A
    DTC B1632 or B1633 is output.
    B
    DTC B1637 or B1638 is output.
    C

    HINT:
    Codes other than DTC B1632 or B1633 and B1637 or B1638 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR (DRIVER SIDE) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

21. CHECK SIDE AIRBAG SENSOR (DRIVER SIDE)

  1. C166120E02
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery.

  1. Interchange the side airbag sensor (Passenger side) with the side airbag sensor (Driver side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1622 and B1627 are not output.
    A
    DTC B1622 is output.
    B
    DTC B1627 is output.
    C

    HINT:
    Codes other than DTC B1622 and B1627 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE SIDE AIRBAG SENSOR (DRIVER SIDE) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1622/81 Lost communication with Side Airbag Sensor RH (+ B1623/81, B1632/81, B1633/81, B1642/81) (from Jul 2010)B1622/81 Lost Communication with Driver Side - Side Airbag Sensor Assembly (+ 5 more codes) (Aug 2008 – Jun 2010) →