2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1622/81 Lost communication with Side Airbag Sensor RH

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH) is composed of the center airbag sensor assembly, side airbag sensor RH and rear airbag sensor RH.
The side airbag sensor RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.
These DTCs are stored when a malfunction is detected for the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).
DTC No.
DTC Detection Condition
Trouble Area
B1622/81
B1623/81
B1632/81
B1633/81
B1642/81
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).
  2. Side airbag sensor RH malfunction
  3. Rear airbag sensor RH malfunction
  4. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Side airbag sensor RH
  3. Rear airbag sensor RH
  4. Center airbag sensor assembly

WIRING DIAGRAM

C165789E38

INSPECTION PROCEDURE


1. CHECK PRESENT DTC
  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for present DTCs (Click here).

    Result:
    Result
    Proceed to
    Present DTC B1623 is output.
    A
    Present DTC B1642 or 81 is output.
    B
    Present DTC B1632 or B1633 is output.
    C
    Present DTC B1622 is output.
    D
    Present DTC B1622, B1623, B1632, B1633, B1642 or 81 is not output.
    E

    HINT:
    1. DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then on (IG) again.
    2. Codes other than DTCs B1622, B1623, B1632, B1633, B1642 and 81 may be output at this time, but they are not related to this check.



B
Go to step 3

C
Go to step 14

D
Go to step 21

E
USE SIMULATION METHOD TO CHECK (Click here)
A


2. CHECK PAST DTC
  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for past DTCs (Click here).

    Result:
    Result
    Proceed to
    Past DTC B1622 or B1632 is not output.
    A
    Past DTC B1632 is output.
    B
    Past DTC B1622 is output.
    C

    HINT:
    Codes other than past DTCs B1622 and B1632 may be output at this time, but they are not related to this check.



B
Go to step 14

C
Go to step 21
A


3. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly, side airbag sensor RH and rear airbag sensor RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly, side airbag sensor RH and rear airbag sensor RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


4. CHECK FLOOR WIRE (OPEN)

  1. Using SST, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.C203033E09

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N23-4 (BBR+) - N23-3 (BBR-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK


5. CHECK FLOOR WIRE (SHORT)

  1. C203032E10
    Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N23-4 (BBR+) - N23-3 (BBR-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


6. CHECK FLOOR WIRE (SHORT TO B+)

  1. C203032E10
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N23-4 (BBR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N23-3 (BBR-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE
OK


7. CHECK FLOOR WIRE (SHORT TO GROUND)

  1. C203032E10
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N23-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    N23-3 (BBR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


8. CHECK FLOOR WIRE (OPEN)

  1. Using SST, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.C213490E07

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N23-1 (BCR+) - N23-2 (BCR-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK


9. CHECK FLOOR WIRE (SHORT)

  1. C213489E07
    Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N23-1 (BCR+) - N23-2 (BCR-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


10. CHECK FLOOR WIRE (SHORT TO B+)

  1. C213489E07
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N23-1 (BCR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N23-2 (BCR-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE
OK


11. CHECK FLOOR WIRE (SHORT TO GROUND)

  1. C213489E07
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N23-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    N23-2 (BCR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


12. CHECK SIDE AIRBAG SENSOR RH

  1. C166177E01
    Connect the connectors to the rear airbag sensor RH and center airbag sensor assembly.

  1. Interchange the side airbag sensor LH with the side airbag sensor RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1623, B1642 or 81 is output.
    A
    DTC B1628, B1647 or 82 is output.
    B
    DTCs B1623, B1642 or 81 and B1628, B1647 or 82 are not output.
    C

    HINT:
    Codes other than DTCs B1623, B1642 or 81 and B1628, B1647 or 82 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


13. CHECK REAR AIRBAG SENSOR RH

  1. C166174E02
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and side airbag sensor RH to their original positions and connect the connectors to them.

  1. Interchange the rear airbag sensor LH with the rear airbag sensor RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1623, B1642 or 81 and B1628, B1647 or 82 are not output.
    A
    DTC B1623, B1642 or 81 is output.
    B
    DTC B1628, B1647 or 82 is output.
    C

    HINT:
    Codes other than DTCs B1623, B1642 or 81 and B1628, B1647 or 82 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

14. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor RH and rear airbag sensor RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


15. CHECK FLOOR WIRE (OPEN)

  1. Using SST, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.C213490E07

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N23-1 (BCR+) - N23-2 (BCR-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK


16. CHECK FLOOR WIRE (SHORT)

  1. C213489E07
    Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N23-1 (BCR+) - N23-2 (BCR-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


17. CHECK FLOOR WIRE (SHORT TO B+)

  1. C213489E07
    Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N23-1 (BCR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N23-2 (BCR-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE
OK


18. CHECK FLOOR WIRE (SHORT TO GROUND)

  1. C213489E07
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N23-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    N23-2 (BCR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


19. CHECK SIDE AIRBAG SENSOR RH

  1. C166177E01
    Connect the connector to the rear airbag sensor RH.

  1. Interchange the side airbag sensor LH with the side airbag sensor RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1632 or B1633 is output.
    A
    DTC B1637 or B1638 is output.
    B
    DTCs B1632 or B1633 and B1637 or B1638 are not output.
    C

    HINT:
    Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


20. CHECK REAR AIRBAG SENSOR RH

  1. C166174E02
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and side airbag sensor RH to their original positions and connect the connectors to them.

  1. Interchange the rear airbag sensor LH with the rear airbag sensor RH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1632 or B1633 and B1637 or B1638 are not output.
    A
    DTC B1632 or B1633 is output.
    B
    DTC B1637 or B1638 is output.
    C

    HINT:
    Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

21. CHECK SIDE AIRBAG SENSOR RH

  1. C166177E01
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Interchange the side airbag sensor LH with the side airbag sensor RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs B1622 and B1627 are not output.
    A
    DTC B1622 is output.
    B
    DTC B1627 is output.
    C

    HINT:
    Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE SIDE AIRBAG SENSOR RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1620/21 Driver Side - Side Airbag Sensor Malfunction (Aug 2008 – Jun 2010)B1622/81 Lost Communication with Driver Side - Side Airbag Sensor Assembly (+ 5 more codes) (May 2007 – Jul 2008) →