2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1627/82 Lost Communication with Front Passenger Side - Side Airbag Sensor Assembly

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010

DESCRIPTION

The front passenger side - side collision sensor circuit (to determine deployment of the front seat side airbag assembly (Passenger side) and curtain shield airbag assembly (Passenger side)) is composed of the center airbag sensor assembly, side airbag sensor (Passenger side) , and rear airbag sensor (Passenger side) .
The side airbag sensor (Passenger side) and rear airbag sensor (Passenger side) detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.
DTC B1627/82, B1628/82, B1637/82, B1638/82, B1647/82, or B1648/82 is recorded when a malfunction is detected in the front passenger side - side collision sensor circuit (to determine deployment of the front seat side airbag assembly (Passenger side) and curtain shield airbag assembly (Passenger side)).
DTC No.
DTC Detection Condition
Trouble Area
B1627/82
B1628/82
B1637/82
B1638/82
B1647/82
B1648/82
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front passenger side - side collision sensor (Passenger side) circuit (to determine deployment of the front seat side airbag assembly (Passenger side) and curtain shield airbag assembly (Passenger side)) for 2 seconds.
  1. Side airbag sensor (Passenger side) malfunction
  1. Rear airbag sensor (Passenger side) malfunction
  1. Center airbag sensor assembly malfunction
  1. Floor wire (for LHD)
  2. Floor wire No. 2 (for RHD)
  3. Side airbag sensor (Passenger side)
  4. Rear airbag sensor (Passenger side)
  5. Center airbag sensor assembly

WIRING DIAGRAM

C169772E02

INSPECTION PROCEDURE


1. CHECK DTC

  1. C157628E02
    Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for present DTCs (Click here).

    Result:
    Result
    Proceed to
    Present DTC B1628 or B1648 is output.
    A
    Present DTC B1647 or 82 is output.
    B
    Present DTC B1637 or B1638 is output.
    C
    Present DTC B1627 is output.
    D
    Present DTC B1627, B1628, B1637, B1638, B1647, B1648, or 82 is not output.
    E

    HINT:
    1. DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then on (IG) again.
    2. Codes other than present DTC B1627, B1628, B1637, B1638, B1647, B1648, and 82 may be output at this time, but they are not related to this check.



B
Go to step 3

C
Go to step 14

D
Go to step 21

E
USE SIMULATION METHOD TO CHECK (Click here)
A


2. CHECK PAST DTC
  1. Check for past DTCs (Click here).

    Result:
    Result
    Proceed to
    Past DTC B1627 or B1637 is not output.
    A
    Past DTC B1637 is output.
    B
    Past DTC B1627 is output.
    C

    HINT:
    Codes other than past DTC B1627 and B1637 may be output at this time, but they are not related to this check.



B
Go to step 14

C
Go to step 21
A


3. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly, rear airbag sensor (Passenger side) and the side airbag sensor (Passenger side).

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly, rear airbag sensor (Passenger side) and side airbag sensor (Passenger side).

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


4. CHECK WIRE HARNESS (OPEN)

  1. Using SST, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.C157702E02

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-4 (BBR+) - N3-3 (BBR-)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-4 (BBL+) - O3-3 (BBL-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


5. CHECK WIRE HARNESS (SHORT)

  1. C157703E02
    Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-4 (BBR+) - N3-3 (BBR-)
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-4 (BBL+) - O3-3 (BBL-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


6. CHECK WIRE HARNESS (SHORT TO B+)

  1. C157703E02
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-4 (BBR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N3-3 (BBR-) - Body ground
    Ignition switch on (IG)
    Below 1 V
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-4 (BBL+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O3-3 (BBL-) - Body ground
    Ignition switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


7. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C157703E02
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    N3-3 (BBR-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    O3-3 (BBL-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


8. CHECK WIRE HARNESS (OPEN)

  1. Using SST, connect terminals 2 (for LHD: (BCR+), for RHD: (BCL+)) and 1 (for LHD: (BCR-), for RHD: (BCL-)) of connector C.C157704E04

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-2 (BCR-) - N3-1 (BCR+)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-2 (BCL-) - O3-1 (BCL+)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


9. CHECK WIRE HARNESS (SHORT)

  1. C157705E04
    Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - N3-2 (BCR-)
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - O3-2 (BCL-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


10. CHECK WIRE HARNESS (SHORT TO B+)

  1. C157705E04
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N3-2 (BCR-) - Body ground
    Ignition switch on (IG)
    Below 1 V
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O3-2 (BCL-) - Body ground
    Ignition switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


11. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C157705E04
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    N3-2 (BCR-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    O3-2 (BCL-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


12. CHECK SIDE AIRBAG SENSOR (PASSENGER SIDE)

  1. C167956E02
    Connect the connector to the rear airbag sensor (Passenger side).

  1. Interchange the side airbag sensor (Driver side) with the side airbag sensor (Passenger Side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1628, B1647, B1648, or 82 is output.
    A
    DTC B1623, B1642, B1643, or 81 is output.
    B
    DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 are not output.
    C

    HINT:
    Codes other than DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR (PASSENGER SIDE) (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


13. CHECK REAR AIRBAG SENSOR (PASSENGER SIDE)

  1. C167953E04
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor (Driver side) and side airbag sensor (Passenger side) to their original positions and connect the connectors to them.

  1. Interchange the rear airbag sensor (Driver side) with the rear airbag sensor (Passenger side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 are not output.
    A
    DTC B1628, B1647, B1648, or 82 is output.
    B
    DTC B1623, B1642, B1643, or 81 is output.
    C

    HINT:
    Codes other than DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR (PASSENGER SIDE) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

14. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor (Passenger side) and the rear airbag sensor (Passenger side).

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the side airbag sensor (Passenger side) and rear airbag sensor (Passenger side).

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


15. CHECK WIRE HARNESS (OPEN)

  1. Using SST, connect terminals 2 (for LHD: (BCR+), for RHD: (BCL+)) and 1 (for LHD: (BCR-), for RHD: (BCL-)) of connector C.C157704E04

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - N3-2 (BCR-)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-2 (BCL-) - O3-1 (BCL+)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


16. CHECK WIRE HARNESS (SHORT)

  1. C157705E04
    Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - N3-2 (BCR-)
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - O3-2 (BCL-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


17. CHECK WIRE HARNESS (SHORT TO B+)

  1. C157705E04
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N3-2 (BCR-) - Body ground
    Ignition switch on (IG)
    Below 1 V
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O3-2 (BCL-) - Body ground
    Ignition switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


18. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C157705E04
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    N3-2 (BCR-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    O3-2 (BCL-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE

C
REPLACE FLOOR WIRE NO. 2
A


19. CHECK SIDE AIRBAG SENSOR (PASSENGER SIDE)

  1. C166177E02
    Connect the connector to the rear airbag sensor (Passenger side).

  1. Interchange the side airbag sensor (Driver side) with the side airbag sensor (Passenger side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1637 or B1638 is output.
    A
    DTC B1632 or B1633 is output.
    B
    DTC B1632 or B1633 and B1637 or B1638 are not output.
    C

    HINT:
    Codes other than DTC B1632 or B1633 and B1637 or B1638 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR (PASSENGER SIDE) (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


20. CHECK REAR AIRBAG SENSOR (PASSENGER SIDE)

  1. C166174E06
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor (Driver side) and side airbag sensor (Passenger side) to their original positions and connect the connectors to them.

  1. Interchange the rear airbag sensor (Driver side) with the rear airbag sensor (Passenger side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1632 or B1633 and B1637 or B1638 are not output.
    A
    DTC B1637 or B1638 is output.
    B
    DTC B1632 or B1633 is output.
    C

    HINT:
    Codes other than DTC B1632 or B1633 and B1637 or B1638 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIRBAG SENSOR (PASSENGER SIDE) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

21. CHECK SIDE AIRBAG SENSOR (PASSENGER SIDE)

  1. C166177E02
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Interchange the side airbag sensor (Driver side) with the side airbag sensor (Passenger side) and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1622 and B1627 are not output.
    A
    DTC B1627 is output.
    B
    DTC B1622 is output.
    C

    HINT:
    Codes other than DTC B1622 and B1627 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE SIDE AIRBAG SENSOR (PASSENGER SIDE) (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← B1627/82 Lost Communication with Front Passenger Side - Side Airbag Sensor Assembly (+ 5 more codes) (May 2007 – Jul 2008)B1630/23 Rear Airbag Sensor RH Circuit Malfunction (from Jul 2010) →